1. Three coils each having resistance 10 2 and inductance L H are connected in delta to a 410V, 50HZ 3-phase supply. If the line current is 12 A, find the following. (a) phase voltage Vp (b) phase impedance Zp (c) inductance L (d) total power Pt (e) draw the circuit diagram for the given three phase RL load in star.

1. Three coils each having resistance 10 2 and inductance L H are connected in delta to a 410V, 50HZ 3-phase supply. If the line current is 12 A, find the following. (a) phase voltage Vp (b) phase impedance Zp (c) inductance L (d) total power Pt (e) draw the circuit diagram for the given three phase RL load in star.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The following diagram shows a three-wire single-phase circuit of a house. Consider that the refrigerator consumes 8.5 A, with an inductive angle of 45°. TV and kitchen loads are 200W and 8kW respectively. Calculate: a) Current line 1, line 2 and neutral. b) Total power of the circuit....
An alternating single phase circuit describes the instantaneous values of the applied voltage and the corresponding current as: v = 360 sin (201,69 t + π/6) and i = 36 sin (201,69 t - π/9) Calculate: the impedance, resistance and reactance of the circuit, the r.m.s.-values of the voltage and current, the true-, apparent- and reactive power in the circuit The time taken to reach -190 V for the second time. Sketch the phasor diagram of this circuit
A series circuit composed of a resistance of 24 ohms, an inductance of 0.09 henry and a capacitance of 8 microfarad, is connected to a 120-volt 50-Hz supply. Calculate (a) the line current, (b) impedance of the circuit, (c) voltage drop, (d) total reactive power, (e) power factor.
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, andadmittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. draw the circuit diagram
A 3- phase star connected load has resistance of 4 Ω, inductance of 15.9mH & a capacitive reactance of 6 Ω respectively in R Y & B phases. If the load is connected to 400V, 50Hz supply, Calculate the neutral current ,Find the total power absorbed by the load., Draw the current and voltage phasors
Circuit elements with an inductance of 200 mH, a capacity of 50 μF and a resistance of 10 Ω are connected in parallel. If the average value of 198 V sinusoidal AC voltage is applied to this system, find the line current, impedance and phase angle of the circuit. (Take the frequency as 60 Hz.)
A non-reactive resistance of 60 Ω is connected in series with a 36 µF capacitor in each phase of a star-connected load.The load is connected to a 260 V, three-phase,50 Hz supply and ABC phase rotation. Use Van as the reference. Calculate the line current,( Ia) in polar form.
In Industry, three Inductive loads, each of resistance R = 30 ohms and inductance L = 0.12 H are connected in Delta to a 430 V, F = 50 Hz, 3 phase supply. Find the following below: Phase Impedance, Zp = Phase Voltage, Vp = Phase current, Ip = Line current, IL= The Total Power Consumed, P =
A 370 kV, three phase transmission line with a 410 km length. The series impedance Z =(0.45+j0.94) Ω/ph/km and shunt admittance y = (j57 x e(-7)) S/ph/km. Evaluate the equivalent π-model and T-model parameters.
A 3-, 400-V symmetrical supply feeds a star-connected load consisting of non-reactive resistors of 3, 4 and 5 connected to the R. Y and 8 lines respectively. The phase sequence is RYB. Calculate (1) the load star point potential (i) current in each resistor and power dissipated in each resistor.
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.
A 3 phase 50 Hz overhead transmission line has the following contants: resistance per phase= 9.6ohms inductance per phase= 0.097 H capacitance per phase= 0.765 uF If the line is supplying a balanced load os 24,000 kVA at 0.8 pf lagging at 66kV, calculate using end condenser method: a. sending durrent b. line value of sending end voltage c. voltage regulation