1. Using superposition of loads, create a single V and M function if a positive bending moment of 11kN/m is added to the beam shown at point C which is the mid of B and D. 2. Draw the V and M diagram if a positive bending moment of 11KN/m is added to the beam shown at point C. 3. Solve for the V and M at just left of point B. 8KN KN 12.2 7.2KN 5:5KN B yo 8M 9:3M 19m

1. Using superposition of loads, create a single V and M function if a positive bending moment of 11kN/m is added to the beam shown at point C which is the mid of B and D. 2. Draw the V and M diagram if a positive bending moment of 11KN/m is added to the beam shown at point C. 3. Solve for the V and M at just left of point B. 8KN KN 12.2 7.2KN 5:5KN B yo 8M 9:3M 19m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7.9 Draw the shearing-force and bending-moment diagrams for the following beams: A cantilever of length 20 m carrying a load of 10 kN at a distance of 15 m from the supported end. A cantilever of length 20 m carrying a load of 10 kN uniformly distributed over the inner 15 m of its length A cantilever of length 12 m carrying a load of 8 kN, applied 5 m from the supported end, and a load of 2kNlm over its whole length A beam, 20 m span, simply-supported at each end and carrying a vertical load of 20 kN at a distance 5 m from one support. A beam, 16 m span, simply-supported at each end and carrying a vertical load of 2.5 kN at a distance of 4 m from one support and the beam itself weighing 500 N per metre.
A 40-lb weight is dropped from a height of h = 2 ft. A 40-lb weight is dropped from a height of h = 2 ft onto the center of the cantilevered A992 steel beam. If the beam is a W10 * 15, determine the maximum bending stress in the beam. onto the center of the cantilevered A992 steel beam. If the beam is a W10 * 15, determine the maximum bending stress in the beam.
Determine the shear force and bending moment in thecompound beam as function of the variables w and l,and draw the shear force and bending momentdiagrams.
Draw the shear and bending moment diagram for the beam.And also show Maximum bending moment Mb=25875lb .ft a tx=9.0ft
Calculate the bending moment in the middle of the beam. L = 6.2 m; q = 5000 N/m and M = 4qL2 Correct given answer is = 1585650
The A992 steel beam shown in Fig. a is a W10 * 39. Determine the maximum bending stress in the beam and the beam’s maximum deflection if the weight W = 1.50 kip is dropped from a height h = 2 in. onto the beam. Est = 29(103) ksi.
Draw the shear and bending moment diagrams of the beam
A beam of length 6 m is simply supported at the ends and carries a uniformly distributed load of 1.5 kN/m run and three concentrated loads of 1 kN, 2 kN and 3 kN acting at a distance of 1.5 m, 3 m and 4.5 m respectively from left end. Draw the S.F. and B.M. diagrams and determine the maximum bending moment.
7.9 Draw the shearing-force and bending-moment diagrams for the following beams: A cantilever of length 12 m carrying a load of 8 kN, applied 5 m from the supported end, and a load of 2kNlm over its whole length
Determine the equations of the shear and bending momentcurves for the beam and loading shown and draw the shearand bending moment curves for the beam and loading. F1= 38 kN w= 14 kN/m
Draw and label the shear and moment diagrams for the beam below. Vmax =_______ Mmax = __________ V =0 @x = __________
Draw the shear and bending moment diagram of the beam