(Find the Resultant Force when ( R_x = 160 Ib .A 25600lb .B 160lb .c 16lb .D 12.64lb
Q: nsidering the various failure cases of the join parts to determine the minimi its of the mechanical…
A:
Q: In an air-conditioning unit 3.5 m3/s air at 27°C dry-bulb temperature, 21°C wet-bulb temperature,…
A:
Q: A steam power plant operates on an ideal reheat-regenerative Rankine cycle and has a net power…
A: From steam table:
Q: 6 in 6 in.- 8 in. if e = 5 degrees and AA' is 5 mm, what is the total deformation of member FC'? O…
A:
Q: How does airfoil work
A:
Q: A transducer element has a speed of sound of 4000 m/s and a density of 7800 kg/m³. What is the…
A: Given Density = 7800 kg/m3 Velocity, V = 4000 m/s Find Theoretical impedance, Z
Q: ( Determine the (f_R ) By using Law of cosine when ( A=8 Ib , B=6 Ib ,c = 100° .A 10 .B 11lb .c…
A:
Q: The wall thickness of a 4-ft diameter spherical tank is 5/16- in. Calculate the allowable internal…
A:
Q: H.W: - Steam at 7 bar & relative humidity 0.08 th condition after throttle.
A: Given:Steam condition before throttle,P1=7 barrelative humidity=0.08after throttle,P2=0.05 bar
Q: Q 21. A cylindrical flask of diameter 4 cm and 14 cm height is half full with water. Determine the…
A:
Q: The wooden members' A and B are to be joined by plywood splice plates that will be fully glued on…
A:
Q: ᴀ ꜱᴛᴇᴇʟ ʜᴀꜱ ᴀ ʙʜɴ = 500. ᴡʜᴀᴛ ɪꜱ ɪᴛꜱ ᴀᴘᴘʀᴏxɪᴍᴀᴛᴇ ᴜʟᴛɪᴍᴀᴛᴇ ꜱᴛʀᴇɴɢᴛʜ ɪɴ ᴍᴘᴀ? a.250000 b. 2225 c.1725…
A:
Q: Choose the letter of the correct answer from the box to match the given topic with 1 appropriate…
A: Enumeration can be defined as the rhetorical device used for listing details or it is a process of…
Q: A particle rotates clockwise in accordance with the equation θ = 32 + 24t – 2t3 where θ is in…
A:
Q: The frame shown in Figure below is supported in pivots at A and B. Each member weighs 800 N/m.…
A:
Q: 2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m?…
A:
Q: Suppose the pump as shown in the figure is operating at free delivery conditions. The pipe, both…
A:
Q: Q1/ For fig shown if water flow rate is 60lit/s, Find (h) Note that Density: Pwater = 1 kg/m³ Pair =…
A:
Q: A non-uniform rod of length L has a linear mass density of 1 = kx² where is k some constant. %3D…
A:
Q: (Problem 6.32 from the text book) Several wooden planks are glued together to form the box beam…
A: Given: vertical shear, V = 3 kN To find: Average shear stress: (a)at A (b)at B
Q: Tmin in cycle = 27 C Tmax in cycle = 1327 C %3D Heat addition during each reheat stage is 25 of the…
A:
Q: An ideal 4-stroke Otto cycle at the beginning of the compression process has air at 1 atm, 20°C and…
A: Find the work done and efficiency of the otto cycle.
Q: The unit of moment .A Ib .B N.m .C N.lb .D Ib.N
A: Answer: ◆ The unit of moment is N•m. ◆ Therefore, the correct answer is option (B).
Q: Consider a system where a horizontal, laminar, separated flow of air and water at 100 kPa pressure…
A: Motivation. The preparation, presentation, and interpretation of experimental findings are covered…
Q: An ideal capacitor with a capacitance of 90.0 nF is charged up to a voltage of 3.00 V. (i) Calculate…
A: GivenC=90nFV=3.0V
Q: 1. An ideal Otto engine, operating on the hot-air standard with k = 1.34, has a compression ratio of…
A: Solution to first three sub-parts as per our company policy:
Q: The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be…
A:
Q: A 4 cm sphere of AISI 316 Stainless Steel begins at 750K. It is cooled by a water spray at 360K with…
A:
Q: Four steel bars jointly support a mass of 15 Mg as shown in Fig. P-276. Each bar has a…
A: As per given question α=11.7 m•c E=200gpa ΔT=50°c We have to find load carried by each bar
Q: State and explain three behaviours of a system.
A: A system is an orderly grouping of interdependent components linked together according to a plan to…
Q: In an air-conditioning unit 3.5 m3/s air at 27°C dry-bulb temperature, 21°C wet-bulb temperature,…
A:
Q: Question 1: Which of the following cross-sections has the largest moment of Inertia (INA)? The…
A: Given:
Q: In an air-conditioning unit 3.5 m3/s air at 27°C dry-bulb temperature, 21°C wet-bulb temperature,…
A:
Q: You have 4 springs, each being 3.5, 6, 8.5, 11 N/m What's the smallest stiffness you can make using…
A:
Q: Describe the mechanism of heat loss in the following scenarios. A computer chip on a motherboard is…
A: Given scenarios : A computer chip on a motherboard is cooled continuously using a small fan to…
Q: Q1/ For fig shown if water flow rate is 60 lit/s , Find (h) Note that Density: Pwater = 1 kg/m³ Pair…
A:
Q: Q 27. Calculate the time period of oscillation (T) of the ship, whose metacentric height is 900 mm…
A: As per given question Metacentric height=900mm Radius of gyration =9m We have to determine the time…
Q: Methane at 2760 kPa and -6.31 °C is compressed in steady-state adiabatic compressor (85% efficient)…
A:
Q: 2. (Problem 6.20 from the text book) A timber beam AB of length L and rectangular cross section…
A: Find the ration of maximum shear stress and maximum normal stress.and also find the dimensions of…
Q: 4. A Cantilever beam deflects downwards when a mass is attached to its free end. The deflection(6)…
A: solving the no. 4 Here we have Note that the slope of the straight line with value of 'Mg'…
Q: For a cantilever beam subjected to a vertical force at its free end, how many elements should be…
A: To find :- How many element should be used for exact solution.
Q: of 1600
A: given:sphere diameter d=4cmsphere temperature Ts=750kwater spray temperature Ta=360kheat transfer…
Q: Air at atmospheric pressure and 25oC is heated in a tube with an ID of 25 mm. The tube wall is…
A: Solution: Given Data: Pi=1.013 barTi=25oCD=25 mmTw=200oCTo=120oCV.=10 Nm3/hr To find: Length of…
Q: The 24T 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 1300 rev/min and is driven at…
A:
Q: This is a diagram of a domestic hot-water system. The gas valve is operated by the controller,…
A: Given : To find : Simplified faut tree Minimal cut sets Minimal path sets
Q: A spring with k= 4500 N/cm supports a mass of 1.5 Kg. Determine the ʼnatural frequency' of this…
A: Stiffness, k= 4500 N/cm= 4500(100) N/m= 450000 N/m Mass, m= 1.5 kg Note: i) Natural frequency of…
Q: 4. For an ideal Diesel cycle with the overall value of k = 1.33, r, = 15, r,=2.1, p, = 97.9 kPa,…
A: Find the mean effective pressure. And pressure at state 2.
Q: This one may be a bit odd, but I can't seem to locate the proper term for a shaft with two flats…
A:
Q: 1. Explain laminar boundary layers and ability to formulate energy equation in a pipe flow system.…
A: Laminar boundary layer
Q: ( Find the Resultant Force when ( R_x = 60.8 Ib , R_y = 192.4 Ib .A 203lb
A: Given:Rx=60.8 lbRy=192.4 lb
Step by step
Solved in 3 steps
- If the component of a force along x-axis is Fx = 20 kN and along y-axis is Fy = 30 kN, and if “t” is an axis making an angle of 30o in the counter clockwise direction with respect to x-axis, what would be the components of this force Ft and Fn along the orthogonal axes “t” and “n”, respectively? Select one: Ft = 2.32 kN and Fn = 35.98 kN Ft = 15.98 kN and Fn = 32.32 kN Ft = 35.98 kN and Fn = 2.32 kN Ft = 32.32 kN and Fn =15.98 kNDraw the correct Free Body Diagram (FBD). Solve the Resultant Force at A. Given F1= 50lb and F2= 80lb.Please draw the following force: Weight (W) at origin C, 270º from Fx = 0º, pointing away from the origin.
- A 30N pair of forces equivalent to these pairs will be placed at points A and B. So what should the AB length be?Q1 / B : 1. Convert the moment of 500 Ib.S to SI units *A bent steel component ABC is designed to carry a distributed load and a concentrated force as shown. The component is fixed at end A. 1. Which of the following is the closest to the perpendicular distance between the x-axis and the concentrated force equivalent to the triangular distributed load? in mm 160, 106.7, 53.3, 40
- Expiremental Method: Force Table F1 - 150N, 30° N of E F2 - 100N, 60° E of S 1) Find the Equilibrant Magnitude and Equilibrant Direction 2) Find Resultant Force Vector Magnitude and %Error 3) Find Resultant Force Vector Direction and %ErrorWhich of the following is false about two-force members? a. The line of action of the internal force in the member is always known. b. The external forces act at only two points on the member. c. The magnitude of the internal force is constant along the length of the member. d. The direction of the internal force in the member is always know/ Which of the following internal forces (and moments) prevents relative rotation about the y-axis of a member? a. Fx b. Fy c. My d. MzDetermine the algebraic sum of the moments of forces relative to a point in F = 10.0 N; m =9.0 Nm, q =8.0 N/m
- Please specify which of the following forces are not conservative forces______. a. Reaction normal force b. Reaction friction force c. Linear Spring Force d. WeightFind the moment (Nm) caused by the force F = 697 N about point D if a= 27 mm and b= 34 mm. Round off only on the final answer expressed in 3 decimals. Note: answers maybe a positive or negative value, following the sign convention discussed on lectures.If F1= 24kN F2=26kN F3=21.5kN R1 = 37.75Nm R2= 33.75Nm calculate the max force the beam is under using the attached image