Question 1 pls. Complete soln and. Corrects units. Thanks 1. Water flows steadily through a closed tank, as in the figure. At section 1, D;= 6 cmand the volume flow is 100 m/h. At section 2, D2 = 5 cm and the average velocity is8 m/s. If D;= 4 cm, what is(0) Qs in m./h and(b) average V, in m/s?Water

Answered: Image /qna-images/answer/08e49b28-dddd-4674-be65-c3bb2f6671a9.jpg

Answered: 1. Water flows steadily through a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C is 7.5 cm in diameter. If the flow in A is divided as follows 2/3 goes to B and 1/3 goes into C, what is the discahrge in pipe A, if the velocity must not exceed 3 m/s in any of the pipes?
Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.
A 6.0 cm diameter horizontal pipe gradually narrows to 4.5 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 33.5 kPa and 22.6 kPa, respectively. What is the volume rate of flow?
In fluid flow equations, the variable p/ϒ is called A. Pressure Head B. Velocity HeadC. Static Head D. Total Head
Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1 tapering to 3.40 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s(b) point 2 m/s
Water enters a shower head through a pipe of internal radius r = 6.4 mm, and leaves through 30 small holes, each of radius r1 = 0.08 mm. When the faucet is opened, the water moves in the tube at a speed of 90 cm/s. What is the volumetric flow of the shower head in liters per second?
PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d’Eau) that is discharged 130 m straight upward (measured from the surface of the lake). The exit of the discharge pipe is 20 cm in diameter.
The large reservoir in the following figure provides water for the indicated tank with a flow rate of 10 L/s. Check that the machine is installed and a pump or a turbine, and determine its power, if the yield is 75%. Suppose ideal fluid. Data: γH20 = 104N/m3 ; ATubes = 10mc2 ; g = 10m/s2 .
A gasoline pump fills a 80-L tank in 1 min 30 s. If the pump exit diameter is 4cm, what is the average pump-flow velocity?
A balloon is being filled with water at an instant when the diameter is 50 cm. If the flow rate into the balloon is 200gal/min, what is the rate of increase in the diameter?
A jet of water of diameter 60 mm strikes a stationary flat plate normally at a velocity of 26 m/s. What is the force exerted by the jet of water? Select one: a. 1,911.3 N b. 1,756.4 N c. 1,561.6 N d. 1,722.1 N
Water at 20°C flows through the orifice in Fig. ,which is monitored by a mercury manometer. If d = 3 cm,(a) what is h when the flow rate is 20 m3/h and (b) what isQ in m3/h when h = 58 cm?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

1. Water flows steadily through a closed tank, as in the figure. At section 1, D;= 6 cm and the volume flow is 100 m/h. At section 2, D2 = 5 cm and the average velocity i 8 m/s. If D;= 4 cm, what is (0) Qa in m;/h and (b) average V; in m/s? (2