Subject: Control System 4.Which one of the following most correctly describes the restrictions on K thatassures that both transient response requirements are met? Show your work for full credit.(a) 0< K < v6(b) 1< K < v6(c) K = V6(d) v6< K(e) No value of K > 0 will satisfy both requirements. 2Electronic PacemakerElectronic pacemakers regulate the speed at which the heart pumps blood. We consider the designof a pacemaker to regulate heart rate, in which the closed-loop dynamicsРасemaker| НеartKDesiredActuals+1heart rateheart rateY(s)are described by the transfer functionR(s)12Kfor K > 0 that is a positive constant.82 + 12s + 12KThe system should satisfy the transient response characteristics: 1) peak time less than or equal to7 seconds, and 2) percent overshoot less than or equal to e- . 100 z 4.32%.

Answered: Image /qna-images/answer/a615ea25-c6a5-4da7-ba2e-b8bcf1f5c1a9.jpg

Answered: 1. Which one of the following most…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the system with forward path gain G(s)=s+5s2+3s+2G(s)=s+5s2+3s+2 and feedback gain H(s)=1s+3H(s)=1s+3, input R(s)=8sR(s)=8s will be applied. Find the steady-state error (ess) that will occur in the system and enter it into the space given below
The mathematical models of some continuous time systems are given above. x(t) is the input signal of the system, and y(t) is the output signal of the system. Which of the following systems is linear and which is nonlinear? For linear systems, write "linear" in the space next to the option. For non-linear systems, write "non-linear" in the space next to the option.
: If F(s) = s 4+ 5s3+20s 2 + 40s + 50 , Investigate the stability of this system
For the system shown in the attached image, assume A = 1300 and n = 860. Draw the root locus for K > 0 and find the range of K for closed-loop stability when:i. G(s) = Kii. G(s) = K(s + 200) / (s + 1000)
Given the plant transfer function, G(s) = 90/ s(s+4) and H(s) = 1. Obtain (i) characteristic equation (ii) damped frequency of oscillation (iii) damping ratio (iv) settling time (v) delay time
control systems In the electromechanical system given below, it can be seen that the coil can be represented by the series R-L circuit and also the coil It is known that the electromagnetic pulling force (F) is also proportional to the coil current, that is, F = βi. The input of the system is the voltage v applied to the coil and the output is the x path taken by the core. Accordingly, the system find the differential equations and transfer function
Consider the mechanical system shown; m is the mass of the body, bis the damping coefficient, k is the stiffness of the spring and F is the applied force. 1) Write the differential equation for the system 2) consifer the force, F, is the input and the displacement of the body of mass, m, is the output of the system. White the transfer function for the system. 3) A proportional controller Kp is applied. Draw the closed loop block diagram for the system. 4)Write the closed loop transfer function for the system with controller Kp.
A self-balancing robot is an inverted-pendulum example problem. The idea is to keep the robot upright by driving the wheels towards the leaning angle theta. When the robot is tilting forward, the wheels should be driven forward with a specific acceleration to counter the tilting. This will keep the robot in an upright position at all times. The block diagram of the system shown in Figure 3 with transfer function of G(s) = 1/s(s+1)(s2+4s+20) and H(s) = 1. a) Sketch the root locus by indicating the poles and zeros location on the loci. b) Locate the asymptotes on the root locus in (a). c) Determine the range of K to keep the system stable. d) Identify the jco axis crossing on the root locus in (a).
A forced excited m–k–c system is under a harmonic force F: F=5000sinωt If the mass m = 50 kg; k=80E3 N/m; damping ratio=0.3 and dynamic deflection is to be less than 0.08 m. Determine the range of operating excitation frequency. Also the show the operating range of frequency on a graph.
A plant has the transfer function given by G(s)=1(s2+3s+1)(s2+7s+1)G(s)=1(s2+3s+1)(s2+7s+1) and is controlled by a proportional controller Gc(s)=KGc(s)=K as shown in the block diagram in Figure. For a stable system, calculate the value of KK that yields a steady-state error E(s)=Y(s)−R(s)E(s)=Y(s)−R(s) with a magnitude less than 0.010.01 for a unit step input.
Solve All parts or will dislike answer A. Find the open-loop transfer function . Y(S) / R(S)B. Find ?(?) when the input ?(?) is a step function (use expansion of partial fractions).C. State the damping factor ?.D. Indicate whether the system is overdamped, underdamped, or critically damped.E. Indicate the natural frequency of the system ??.F. Indicate the poles and zeros of the system.G. Use the end theorem to find the steady-state value.H. Find ?(?) (use inverse Laplace transform).I. Plot the time response of the system.
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

1. Which one of the following most correctly describes the restrictions on K that assures that both transient response requirements are met? Show your work for full credit. (a) 0< K < v6 (b) 1< K < v6 (c) K = /6 (d) v6< K (e) No value of K > 0 will satisfy both requirements.