1.0. Size = Q4: Estimate the permissible stress for a Ck 60 steel gear shaft of 100 mm outer diameter with strength 660MPa tested for 10 mm diameter shaft. If the impact safety factor is 1.5, and the load error factor C assumed 25% load additional due to inertia forces and at 300 °F elevated temperature. Univer raq

1.0. Size = Q4: Estimate the permissible stress for a Ck 60 steel gear shaft of 100 mm outer diameter with strength 660MPa tested for 10 mm diameter shaft. If the impact safety factor is 1.5, and the load error factor C assumed 25% load additional due to inertia forces and at 300 °F elevated temperature. Univer raq

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer this question! And plss box your final answer. 1.) A 15-It beam simply supported at the ends cartes a concentrated load of 9000 b at midspan. Select the lightest Ssection that can be employed using an allowable stress of 18 ksl. What is the actual maximumn stress in the beam selected?
A reinforced concrete T-beam has the following properties: Flange width, bf = 1350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f'c = 21 MPa Steel strength, fy = 415 MPa If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage (mm, 2 decimal places). What is the condition of failure? (Balanced, Tension controlled, Compression controlled, Transition). Calculate the design moment strength of a typical interior beam (kN-m, whole number).
1. The following are factors considered in assigning factor of safety due to consequences of failure except a. Variation in the strength of materials purchased b. Direct cost of clearing the debris c. Replacing the structure and its contents d. None of the choices 5. Calculate the depth of neutral axis at balanced condition if the effective depth is 250 mm and fy is 415 MPa. a. 147.78 mm b. 212.50 mm c. 294.12 mm d. 223.25 mm 6. Calculate the stress at the centroid of the tension steel in single layer if the effective depth is 250 mm and the depth of neural axis is 100 mm. a. 800 MPa b. 500 MPa c. 1000 MPa d. 900 MPa 7. Calculate the strain at the centroid of the tension steel in single layer if the effective depth is 250 mm and the depth of neural axis is 100 mm. a. 0.0040 b. 0.0025 c. 0.0050 d. 0.0045
A simply supported rectangular beam of length 5m has a width of 300mm and an effective depth of 500mm. The beam is to be reinforced using 12mm bars. The beam supports service dead loads of 25 kN/m and 30 kN/m, respectively. f'c= 28 MPa, fy= 420 MPa 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam. Expert Solution
A piece of engineering equipment is supported by thefoundation shown. The diameter of the circular pin is 20 mm. a.) Determine the value of P so as not to exceed the allowable bearing stress of 310.5 Mpa in the circular pin.b.) Determine the value of P so as not to exceed the allowable shearing stress of 138 Mpa in the circular pin.
A rectangular reinforced concrete beam has a cross-section dimensions b=400mm andoverall depth h= 800mm. The beam as shown in the image below carries asuperimposed dead load of 12 kN/m (excluding the self-Weight of the beam) andspecified live load of 20 kN/m. The beam has a compressive strength of 30Mpa andreinforcement yield strength of 400 Mpa a) What is the self weight of the beam? b) What is the modulus of elasticy and yeild strain of reinforcement
8. Two flat jacks, 12 in. square, are placed in the w: 3 mately circular test gallery 8 ft in diameter. na:!;a:;d ?: iﬁﬁ.ﬁ'ﬁf& placed in the side wall. Flat jack 2 is vertical, with its edge parallel to the axis of the gallery. The cancellation pressures measured were 2500 psi with FJ 1 and 900 psi with FJ 2. Estimate the initial stresses (vertical and hori- zontal). List your assumptions.
A solid circular shaft, 15 mm in diameter, is subjected to torsional shear stress, which varies from 0 to 35 N/mm⅔ and at the same time is subjected to an axial stress that varies from -15 to +30 N/mm². The frequency of variation of these stresses is equal to the shaft speed. The shaft is made of steel FeE 400 (Sut=540N/mm²) and the corrected endurance strength of the shaft is 200 N/mm². Determine the factor of safety.
d. Secant modulus at a stress of 62 ksi.e. Tangent modulus at a stress of 65 ksi.
PLEASE ANSWER ASAP TY! a) What is the magnitude of internal torque in segment CD (in N-m)? b) What is the magnitude of internal torque in segment AC (in N-m)? c) What is the magnitude of torsional shear stress in segment DB (in MPa)? d) Determine the maximum torsional shear stress in the shaft (in MPa). e) What is the angle of twist of the shaft at B relative to A (in degrees)?
A 4.75-in. outside diameter polyethylenepipe designed to carry chemical waste is placedin a trench and bent around a quarter-circular 908bend (see figure). The bent section of the pipe is52 ft long.(a) Determine the maximum compressive strainεmax in the pipe.(b) If the normal strain cannot exceed 6.1x10 -3 ,what is the maximum diameter of the pipe?(c) If d = 4.75 in., what is the minimum acceptablelength of the bent section of the pipe?
A water tank is 8 meters in diameter and 12 meters high. Ifthe tank is to be completely filled, determine the minimumthickness of the tank plating if the stress is limited to40 MPa.