1.1 Explain how to test a semiconductor diode whether it is defected or not, by means of an ohmmeter? 1.2 For the circuit given in Fig. 1, Dı is a diode, V1=5V, R1=1kN ,and Rpor=lkQ find the voltage Vp and current Ip. ID R1 RPot - V1 D1 V Vo Figure 1. 1.3 For the circuit given in Fig. 2, D1 is a diode, Vi=5V, R1=1kM ,and Rpor=lkN find the voltage Vp and current Ip. a ID R1 RPot > D1 A VD Figure 2.

1.1 Explain how to test a semiconductor diode whether it is defected or not, by means of an ohmmeter? 1.2 For the circuit given in Fig. 1, Dı is a diode, V1=5V, R1=1kN ,and Rpor=lkQ find the voltage Vp and current Ip. ID R1 RPot - V1 D1 V Vo Figure 1. 1.3 For the circuit given in Fig. 2, D1 is a diode, Vi=5V, R1=1kM ,and Rpor=lkN find the voltage Vp and current Ip. a ID R1 RPot > D1 A VD Figure 2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit given in Fig. 1, D1 is a diode, V1=5V, R1=1kΩ ,and RPot=1kΩ find the voltage VD and current ID.
A 1N4733 zener diode has a Zz of 7 ohms. Considering the data of the manufacturer's hona, the Vz = 5.1 V with a test current, Iz, of 49 mA. What is the voltage across the zener terminals when the current is 65 mA? When the current is 25 mA? Include the graph where these values are shown.
Please give the step-by-step solution.Determine the following: (1) Vrdg (2)Ardg (2) Iave/diode (4) Ipk/diode (5) Pl(ave) (6) PIV/diode
ELECTRONİC1 Consider the graphical analysis of the diode circuit of Fig.1 with VDD = 1V , R = 1K ohm, and a diodehaving Is = 10−15A. Calculate a small number of points on the diode characteristic in the vicinity ofwhere you expect the load line to intersect it, and use a graphical process to refine your estimate ofdiode current. What value of diode current and voltage do you find? Analytically, find the voltagecorresponding to your estimate of current. By how much does it differ from the graphically estimatedvalue?
The high-voltage power supply for a television's picture tube has an open-circuit voltage of 18 kV and an internal resistance of 1.5 MQ. (a) Find the voltage at the anode of the picture tube when the anode current is 800 µA. (b) What will the anode voltage be if the anode current is increased by 50%? (c) Find the short-circuit current of the power supply
A shunt regulator employs a zener diode for which VZ = 10.1 V at IZ = 10 mA while VZ = 10.2 Vat IZ = 20 mA. The available supply voltage (VS) is 15.0 V, R = 300 ohm, and the load resistance(RL) =1.0 kohma) Find VZ0 and rz.b) Calculate the output voltage (VO).c) Determine the line regulation (ΔVO/ΔVS).d) Using the line regulation obtained in (c), determine the values of the output voltage (VO) if thesupply voltage (VS) is increased from 15 V to 15.1 V.
Apply each of diodeapproximations and determine:a. Current through D1b. Voltage across D2c. Voltage across R3 GIVEN: R1 = 2 kΩ, R2 = 1.2 kΩ, R3 = 6.8 kΩ E= 10 V D1: Si, rB = 2 Ω, rR = 220 kΩ D2: Si, rB = 5 Ω, rR = 560 kΩ DETERMING FIRST IF IT IS A FORWARD BIASED OR REVERSED BIASED THEN, SOLVE IN FIRST APPROXIMATION, SECOND APPROXIMATION AND THIRD APPROXIMATION SHOW THE CIRCUIT DIAGRAM IN EACH APPROXIMATION
A sample of silicon have electron concentration 3.2x10^11 m^-3 and L=86 mm, t=10 mm and w=35 mm, when sample is tested by Hall effect, the value of resistance 2.7 K ohm and the Hall coefficient=3.6 m^3/c, is obtained. 1. Which kind of semiconductor that the sample? 2. Determine the value of mobility for the sample in (1).
A silicon semiconductor is in the shape of a rectangular bar with a crosssectional area of 10 μm × 10 μm, a length of 0.1 cm, and is doped with Arsenic at 5 × 1016 atoms/cm3 concentration. (T = 300 K).a) determine the current if 5 V is applied across the length. b) repeat part (a) if the length is reduced to 0.01 cm. c) calculate the average drift velocity of electrons in parts (a) and (b). (µn=1350 cm2/volt-s)
Sketch the output waveform for the clipping circuit of Fig.1, if a load resistance RL of value1 kΩ is connected at the output terminals in parallel with the diode.
A 1 mm long bar of Si ar 300K is doped with donor impurity to the extent of 5 x 10^10 cm^-3. Find the voltage across the bar if current density in the bar is 1 mA cm^-2
For silicon at T = 500 Kwith donor density N_D = 5 *10^{13} cm^{-3} and acceptor density N_A = 0, calculate the equilibrium electron concentration in cm^{-3} In this problem, you can assume the bandgap energy and effective masses are independent of temperature and use the room temperature values for them. Values within 5% error will be considered correct.