1.12 The frame shown consists of four wooden members, ABC, DEF,BE, and CF. Knowing that each member has a 2 X 4-in. rectan-gular cross section and that each pin has a 2-in. diameter, deter-mine the maximum value of the average normal stress(a) in member BE, (b) in member CF.45 in.30 in.-IcB40 in.D-15 in.-4 in.E30 in.-4 in.480 lb

To find stress in member BE ,CF

1.12 The frame shown consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each member has a 2 x 4-in. rectan- gular cross section and that each pin has a -in. diameter, deter- mine the maximum value of the average normal stress (a) in member BE, (b) in member CF. 45 in. 30 in.- A 480 lb 40 in. D-15 in.- 4 in. E 30 in.- 4 in.

1.12 The frame shown consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each member has a 2 x 4-in. rectan- gular cross section and that each pin has a -in. diameter, deter- mine the maximum value of the average normal stress (a) in member BE, (b) in member CF. 45 in. 30 in.- A 480 lb 40 in. D-15 in.- 4 in. E 30 in.- 4 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Data are as follows: P = 6.2 kN, L = 3.2 m, d = 1.25 m, b = 80 mm, t = 25 mm, h = 120 mm, and h1 = 90 mm. (1) Locate the position of the neutral axis in the cross section as shown in Fig.3-a. ((2) Determine the maximum tensile stress σt,max and maximum compressive stress σc,max due to the load P acting on the simple beam AB, if the cross section has the moment of inertial about the neutral axis is IZ = 5.88×10-6 m4. A freight-car axle AB is loaded approximately as shown in Fig.3-b, with the forces P representing the car loads and the forces R representing the rail loads. The diameter of the axle is d = 82 mm, the distance between centers of the rails is L, and the distance between the forces P and R is b = 220 mm. Please calculate the maximum bending stress σmax in the axle if P = 50 kN.
Determine the axial stress in member BE of the loaded truss if it has a circular cross-section with a diameter of 20 mm.
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
A simply supported rectangular concrete beam 6m long is reinforced with four-28mm diam tension bars and two-28mm diam. compression bars. The beam has a width of 300mm and overall depth of 400mm. The steel covering to the centroid of reinforcements is 70mm, fc’=30 MPa and fy=418 MPa. a. Draw the stress diagram b. Compute for the Ultimate moment capacity of the beam
A 30-mm-diameter solid steel shaft supports loads PA = 1300 N and PC = 2880 N, as shown. Assume LAB = 99 mm, LBC = 196 mm, and LCD = 144 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude σmaxσmax and location x (measured positive to the left from D) of the maximum bending stress in the shaft.
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa GIVEN: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
The steel shaft shown rotates at 4 Hz with 35 kW taken off at A, 20 kW removed at B, and 55 kW applied at C. Using G = 83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C. NOTE: SHOW FREE BODY DIAGRAM AND COMPLETE SOLUTON
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa GIVEN: b= 350 mm d= 600 mm L= 6 m Wd = 13 kN/m WL = 36 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of compression block of the section in PART B in mm.0 Calculate the depth of the neutral axis of the section in PART B in mm.0 Calculate the stress in the steel of the section in PART B in MPa.0 Calculate the ultimate moment capacity of the section in PART B in kN.m.0
2 - For beam I with distributed and concentrated loads, determine: a)The maximum shear stresses of interest along the beam height (draw the stress diagram); B)How far should the screws be placed along the beam so that resist shear. *Consider that each screws resists 6kN to shear.