Pressurized steam flows through a pipe of 0.6 m diameter. The pipe is embedded in a concrete block ,conductivity k = 1.4 W/mK ,with a square cross sectional length, w = 1 m . The required surface temperature values are 401 and 301 in K. Calculate the heat loss from the pipe per unit length. w Concrete T1 T2 D = 0.6 m

Pressurized steam flows through a pipe of 0.6 m diameter. The pipe is embedded in a concrete block ,conductivity k = 1.4 W/mK ,with a square cross sectional length, w = 1 m . The required surface temperature values are 401 and 301 in K. Calculate the heat loss from the pipe per unit length. w Concrete T1 T2 D = 0.6 m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.4P: An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a...

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
Consider a closed cylindrical reactor vessel of diameter D= 1 ft, and length L= 1.5 ft. The surface temperature of the vessel, T1, and the surrounding temperature, T2, are 390 deg. F and 50 deg. F, respectively. The convective heat transfer coefficient, h, between the vessel wall and surrounding fluid is 4.0 Btu/h . ft . ⁰F. Calculate the thermal resistance in ⁰F .h/Btu.
The rate of heat transfer per unit area from a metal plate is 1000 W/m^2 . The surface temperature of the plate is 120°C, and ambient temperature is 20°C. Estimate the convective heat transfer coefficient.
A horizontal pipe having a surface temperature of 67 °C and diameter of 25 cm is buried at a depth of 1.2 m in the earth at a location where k = 1.8 W/m-°C. The earth surface temperature is 15 °C. Calculate the shape factor if the pipe length is 10 m.
Calculate the quantity of heat conducted per minute through a duralumin circular disc 119mm diameter and 22.65mm thick when the temperature drop across the thickness of the plate is 9.3°F take the coefficient of thermal conductivity of duralumin as 150 W/m-K. Answer: 22.833 kJ/min
A fluid has a temperature of 100C and thermal film coefficient of 50 W/m^2-K. Solve for the heat transferred per sq m of contact if the surface it is in contact with has a surface temperature of 20C.
The cylindrical pipe with a thread diameter of 0.070 m and an internal diameter of 0.050 m is insulated both internally and externally. Calculate the heat loss per unit length of the pipe (1 m) when the inner surface temperature of the pipe is kept at 50 °C and the outer surface temperature at 20 °C (Average thermal conductivity constant = Km= 0.172 J/cm.s.K).
HEAT TRANSFER A mild steel steam pipe with an outer diameter of 11.43 cm and inner diameter of 10.226 cm is covered with 2.5 cm layer of 85% magnesia. The outer surface temperature is 65°C. Determine the heat loss per hour per meter of the pipe. Assuming that the steam is saturated at the pressure of 1.14 MPa, its temperature is 185.68°C. k (steel) = 55.4; k (magnesia, 85%) = 0.0727 W/m-K