Calculate the rate of heat transfer by natural convection between a shed roof of area 20m x 20m and ambient air, if the roof surface temperature is 27 C, the air temperature is -3 C, and the average convection heat transfer coefficient is 10 W/m K.

Calculate the rate of heat transfer by natural convection between a shed roof of area 20m x 20m and ambient air, if the roof surface temperature is 27 C, the air temperature is -3 C, and the average convection heat transfer coefficient is 10 W/m K.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.17P: The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with...

See similar textbooks

Related questions

Q: A 1.27-cm diameter copper (r = 8933 kg/m3, C = 385 J/(kg °C)) sphere is heated in a convection…

Q: A 6 cm diameter cylinder is initially at a temperature of 10 °C. Later, this cylinder was thrown…

Q: A 0.5-m-diameter pipe (ɛ = 0.9) carrying steam has a surface temperature of 500 K (see Fig. 1.25).…

A: Given data as per question surface temperature =500 k Room temperature =300 k convective heat…

Q: A hot surface at 100°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k…

A: Given: The temperature of hot surface, Ti = 100°C The length of fins, L = 3 cm The diameter of fins,…

Q: A food product with 73% moisture content in a 5 cm diameter can wants to be frozen. The density of…

Q: One side of a 2-m-high and 3-m-wide vertical plate at 80°C is to be cooled by attaching aluminum…

Q: A 15-ft long strip of sheet metal is being transported on a conveyor at a velocity of 16 ft/s. To…

A: Given that,

Q: A rectangular fin with k=43 W/m.C, thickness t=2 cm, length L=14 cm and width W=1 m. The base of the…

Q: A fabricated food, in the form of small spherical pellets, is to be frozen in an air-blast freezer.…

A: given data: initial temoerature of product(T1)=250cmedium temperature(T)=-400cfreezing…

Q: A food product with 73% moisture content in a 7 cm diameter can wants to be frozen. The density of…

A: GIVEN:food product with 73% moisture contentdiameter=7 cmdensity of the product is 970 kg/m³thermal…

Q: A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. The density of…

Q: NUMBER 3 A food product with 80% moisture content in a 10 cm diameter can wants to be frozen. The…

A: Given: d=10 cmρ=1000 kg/m3k=1.0 w/mKTi=-2.5 CT∞=-40°CTf=-10°Ct=8 hrs

Q: Derive the expression for overall heat transfer coefficient through a two layers composite sphere…

Q: Two coaxial spheres with diameters of 15 cm and 25 cm were separated by air at 1 atm pressure. two…

Q: two 5 cm diameter, 15 cm long aluminum bars (k=176W/m(degrees Celsius)) with ground surfaces are…

Q: In a slaughter house, 10-cm-thick meat slab initially at 15°C are to be cooled in the racks of a…

Q: Q18: Heat is generated uniformly at a rate of 2.6 x10 W/m3 in a spherical ball (k = 45 W/m C) of…

Q: A food product with 73% moisture content in a 10 cm diameter can wants to be frozen. The density of…

A: Given: d=10 cmρ=970 kg/m3k=1.2 W/mKTi=-1.75°Ct= 15 hrsT∞=-25°CTf=-10°C As the moisture content is…

Q: One end of a 0.3 m long steel rod is connected to a wall at 204°C. The other end is connected to a…

Q: One side of a 2-m-high and 3-m-wide vertical plate at 80°C is to be cooled by attaching aluminum…

A: The Answer is below

Q: A hot surface at 100°C is to be cooled by attaching3-cm-long, 0.25-cm-diameter aluminum pin fins (k…

A: The heat transfer by one fin is given as, For parameter m, it is written as The corrected length…

Q: [1]A house has a composite wall of wood, fiberglass insulation, and plaster board, as indicated in…

Q: ou have experienced convection cooling if you have ever extended your handout of the window of a…

A: given data; temperature at hand (T)=300c(a)⇒vehicle speed…

Q: A long aluminum cylinder with a diameter of 5 cm is initially at a temperature of 200°C and is…

Q: Ground turkey was made into me at balls and refrigerated at 2 ° C before being deep fried. The…

A: Given information:Diameter of the ball is =9cmRefrigerated temperature is=Cooked over temperature…

Q: A cylindrical rod with 20 cm diameter and 5 m length initially at a uniform temperature of 500°C is…

A: Given data:

Q: |A 3 m internal diameter spherical tank made of 1 cm thick stainless steel (k = 15 W/mK) is used to…

Q: Water flows at 67 C inside a 2.5 cm inside diameter tube such that hi = 3500 W/m² .C. The tube has a…

Q: A food product with 80% moisture content in a 5 cm diameter can wants to be frozen. The density of…

A: Given: Diameter of the food product, a = 5 cm = 0.05 m Freezer room temperature, Ta = -35°C = 238 K…

Q: The roof of a house consists of an 18 cm-thick concrete slab (k = 2 W/m • °C) that is 15 m wide and…

Q: A food product with 73% moisture content in a 10 cm diameter can wants to be frozen. The density of…

A: Given data, x = Moisture contains in the food product = 0.73 a = Diameter of the food product = 0.1…

Q: A hot plate of length 0.75 m, width 0.5 m, and thickness 2 cm is placed in an air stream at 20°C. It…

A: The solution is in the following stpes

Q: A house has a composite wall of wood, fiberglass insulation, and plaster board, as indicated in the…

A: Data given- hi =30 W/m2-K A = 350 m2 Ti = 20° C To = -15°C ho = 60 W/m2-K Material are…

Q: A food product with 80% moisture content in a 10 cm diameter can wants to be frozen. The density of…

Q: The wall of a cold storage room is composed of brick, concrete and cork insulation with thickness of…

Q: A house has a composite wall of wood, fiberglass insulation, and plaster board, as indicated in the…

A: a. From properties of material table,Conductivity,kb=0.038 W/m.Kks=0.038 W/m.Kkp=0.038 W/m.K Total…

Q: . A steel ball [c-0.46 kJ/kg C, k-35 W/m. C] 5.0 cm in diameter and initially at a uniform…

Q: A food product with 73% moisture content in a 7 cm diameter can wants to be frozen. The density of…

A: Moisture content = 73% = 0.73 Density = 970 kg / m³ Diameter = 7 cm = 0.07 m Thermal conductivity =…

Q: 3. A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. The density…

A: GIVEN:diameter of tabk, d=7cmdensity, p=1000kg/m3initial freezing temp, T=-2'Ctime,…

Q: Number 3 A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. The…

A: Write the given values using suitable variables. Here Mm signifies moisture content, d signifies…

Q: A person is found dead at 5 PM in a room whose temperature is 20°C. The temperature of the body is…

Q: Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. The water flow…

A: Convective heat-transfer coefficient, h = 15 W/m2-K diameter of the apple, da = 10 cm = 0.1 m The…

Q: A horizontal thin plate with a length of L= 10 cm is tiled with a constant heat flux from the bottom…

Q: An engine block with a surface area measured to be 0.95 m2 generates a power output of 50 kW with a…

A: Write the expression of the efficiency of the engine.

Q: At what rate is heat lost through a 1.3m ×2.7m rectangular glass window that is 0.32cm thick when…

Q: One side of a 2-m-high and 3-m-wide vertical plate at 80°C is to be cooled by attaching aluminum…

Q: D. (30%) A planar steel plate (k= 100 w/m-°k) of thickness of 20 cm, with an inner heat generation…

Q: A furnace wall comprises three layers of thickness 250 mm, 100 mm, and 150 mm with thermal…

Question

Answer:

Calculate the rate of heat transfer by natural convection between a shed roof of area 20m x 20m and ambient air, if the roof surface
temperature is 27 C, the air temperature is -3 C, and the average convection heat transfer coefficient is 10 W/m K.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.
A horizontal, 3-mm-thick flat-copper plate, 1-m long and 0.5-m wide, is exposed in air at 27C to radiation from the sun. If the total rate of solar radiation absorbed is 300 W and the combined radiation and convection heat transfer coefficients on the upper and lower surfaces are 20 and 15W/m2K, respectively, determine the equilibrium temperature of the plate.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.