1.24 An optical source is selected from a batch characterized as having lifetimes that follow a slow internal degradation mode. The -3-dB mean time to failure of these devices at room temperature is specified as 5 x 10“ h. If the device emits 1 mWat room temperature, what is the expected optical output power after 1 month

1.24 An optical source is selected from a batch characterized as having lifetimes that follow a slow internal degradation mode. The -3-dB mean time to failure of these devices at room temperature is specified as 5 x 10“ h. If the device emits 1 mWat room temperature, what is the expected optical output power after 1 month

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the transistor , IS = 6×10−16 μA,αF = 0.985, and αR = 0.25. (a) What type oftransistor is in this circuit? (b) Label the collector, base, and emitter terminals of the transistor.(c) Label the emitter-base and collector-base voltages, and label the normal direction for IE , IC, andIB. (d) Write the simplified form of the transportmodel equations that apply to this particular circuitconfiguration. Write an expression for IE /IC. Writean expression for IE /IB. (e) Find the values of IE ,IC, IB, βF , βR, VE B, and VC B.
For the transistor , IS = 4 × 10−16 μA,βF = 75, and βR = 4. (a) Label the collector, base,and emitter terminals of the transistor. (b) What isthe transistor type? (c) Label the emitter-base andcollector-base voltages, and label the normal direction for IE , IC, and IB. (d) Write the simplified formof the transport model equations that apply to thisparticular circuit configuration. Write an expressionfor IE /IB. Write an expression for IE /IC. (e) Findthe values of IE , IC, IB, VC B, and VE B.
Create a theoretical framework of improving efficiency of solar panel using optical disc such as cd,dvd, and blu-ray
With the conditions given below, if voltage is v(t) = 8sin4000pit mV, with the osciloscope, What are the Vs, Vd, Hs, and Hd?
a cassette player is said to have a signal to noise ratio of 58dB whereas for a CD player it is 95dB. what is the ratio of intensities of the signal and background noise for each device?
H5. The DEIMOS camera attached to the KECK telescope uses an array of 16 CCDs. Each CCD is an array of 2048 X 4096 pixels. What CTE value should we have so that the charge transfer occurs with 99.9% efficiency from the first pixel of the first CCD to the CCDs output node?
A GaAlAs LED with an active region width of 1.5 μm operates at 300K at a current density of 120A/cm2. Assuming that the steady state electron density is n=1017 cm-3calculate the carrier lifetime. Also calculate the optical 3-dB cut-off frequency
An equivalent circuit for a piezoelectric accelerometer, which uses a quartz crystal as the sensing element, is shown in the following figure. The generated charge is denoted by q and the output voltage at the end of the accelerometer cable is vo. The piezoelectric sensor capacitance is modeled by Cp and the overall capacitance experienced at the sensor output, whose primary contribution is due to cable capacitance, is denoted by Cc. The resistance of the electric insulation in the accelerometer is denoted by R. Write a differential equation relating vo to q. What is the corresponding transfer function? Using this result, show that the accuracy of the accelerometer improves when the sensor time constant is large and when the frequency of the measured acceleration is high. For a quartz crystal sensor with R = 1 × 1011 Ω and Cp = 300 pF, and a circuit with Cc = 700 pF, compute the time constant.
Consider a non-ideal MOSFET that has been fabricated on a siliconwafer with initial uniform boron doping of 7.5 × 1015 cm-3. The gateoxide has a thickness tox = 35 nm, fixed charge Qf /q = 5.0 × 1010 cm-2and mobile charge Qm /q = 2.5 × 1010 cm-2 (assume other oxidecharges are negligibly small). The gate has been fabricated frompolysilicon to give a gate length of 150 nm. The work functiondifference between the polysilicon gate and the silicon is –0.35 V.Assuming a temperature of 300 K and ignoring short channel effects,calculate the threshold voltage of the MOSFET if there is zero biasapplied between the source and the silicon substrate.
Consider a common emitter amplifier circuit with Rc= 4.7 K Ohm and bypass capacitor of 120uF, calculate: 1.VCC such that Open circuit VCE=10 V, 2.R2 to make VB= 1.75 V given that R1= 47K ohm 3.RE2 to make re'=22 Ohm if RE1=470 Ohm 4.the expected no load gain with bypass capacitor across RE2 please please in 20 minutes
Consider a common emitter amplifier circuit with Rc= 4.7 K Ohm and bypass capacitor of 120uF, calculate: 1.VCC such that Open circuit VCE=10 V, 2.R2 to make VB= 1.75 V given that R1= 47K ohm 3.RE2 to make re'=22 Ohm if RE1=470 Ohm 4.the expected no load gain with bypass capacitor across RE2 5.the expected gain with 47K ohm load and with bypass capacitor across RE2 6.the gain with 47K ohm load and no bypass capacitor it a one question please solve it all i do not know how to divided please please in 30 minutes
A radiograph is produced using 80kVp and 50mAs at 40 inches. If I change to 90kVp at 72 inches and use the 400mA station, how much time is needed to produce the same density?