4.5 The principal stresses induced at a point ina machine component made of steel 50C4(S,= 460 N/mm2) are as follows:%3Dytoj = 200N/mm? 02 = 150 N/mm? 03 =0Calculate the factor of safety by (i) themaximum shear stress theory, and (ii) thedistortion energy theory.%3D(i) 2.3 (ii) 2.55]

Answered: Image /qna-images/answer/dbdf53bb-d7c2-41d8-ba83-c6fd0490b001.jpg

1.5 The principal stresses induced at a point in a machine component made of steel 50C4 (S= 460 N/mm?) are as follows: o = 200N/mm? 0, = 150 N/mm? 03 =0 Calculate the factor of safety by (i) the maximum shear stress theory, and (ii) the distortion energy theory. %3D %3D %3D () 2.3 (ii) 2.55]

1.5 The principal stresses induced at a point in a machine component made of steel 50C4 (S= 460 N/mm?) are as follows: o = 200N/mm? 0, = 150 N/mm? 03 =0 Calculate the factor of safety by (i) the maximum shear stress theory, and (ii) the distortion energy theory. %3D %3D %3D () 2.3 (ii) 2.55]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
A plane stress state is given by the principal stresses σx =25 MPa and σy= -11 MPa. Determine σx' in the case that the system is inclined by 30 degrees (counter-clockwise). Give your answer in MPa to the nearest whole number.
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: -all 3 principle stresses, the max in plane stress, average noemal stress and the absolut max shear stress. - Show the principle stress, the max inplane shear stress and the average normal stress on an appropriate schematic
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: All three principle stresses, the max in plane shear stress, average normal stress and absolute max shear stress
A closed cylinder (92) cm long, containing 3 MPa pressurized fluid, due to this pressure a change in volume and change in length occurs has the values 1.535 × 10-6 m3 and 4.2 × 10-5 m3, respectively. Determine: (a) the diameter and thickness of the cylinder.(b) the hoop and longitudinal stresses. (c) to what value can the fluid pressure be increased before failure occurs according to the maximum principal stress theory of elastic failure?(d) under the pressure produced in (c), what will be the extra fluid required to pumped into the cylinder. For the material of the cylinder, E = 200 GPa, v = 0.3, and the yield stress σy in simple tension 280 MPa.
4-Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 50 mm x 31 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 22 kN (tensile), 30 kN (compressive), 22 kN (compressive) respectively. Take E as 100 GPa, Poisson’s ratio as 0.3 The stress along length direction (Unit in MN/m2)= _____________ The compressive stress along width direction (Unit in MN/m2)= _____________ The compressive stress along depth direction (Unit in MN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
At a point in an elastic material under strain, the stresses on the three mutually perpendicular planes are as follows:A normal tensile stress of 60 N/mm^2and shear stress of 40 N/mm2 on one plane and a normal tensile force of 40 N/mm^2and a complimentary shear stress of 40 N/mm^2 on another plane. Find the following using Mohr circle only (take 5 N/mm2 = 1 cm)a. The principal stresses and principal planes.b. The maximum shear stress and its plane.c. The normal and shear stress on a plane inclined at an angle of 30Oto major principal plane.
1-A bar of square cross section is subjected to point loads of P1, P2, P3 and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 110 kN, P2 = 210 kN & P4 = 190 kN. Also, determine the stresses in each section & the net change in the length of steel bar. square of size a1=50mm, L1=30 cm, size a2 = 40mm, L2=39 cm, size a3=50 mm & L3 =32 cm Take E = 166 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is
1. A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the bulk modulus given that the Young’s modulus E is 214 Gpa and the Poisson’s ratio is 0.33. Also determine the change in the volume.2. Starting from the first principles derive the relation between Young’s modulus (E), shear modulus (G) and Poisson’s ratio (υ)
The principal strains in a plane, measured experimentally at a point on the aluminum fuselage of a jet aircraft, is ε1 = 117x 10^6, and ε2 = 167 x 10^6. If this is a case of plane stress, determine the associated principal stresses at thepoint in the same plane.
3.For a body under three dimensional stress state, describe the procedure for obtaining the absolute maximum shearing stress at a given point. What is meant by strain transformation? Describe two procedures for obtaining stress form Mohr’s circle for strain.