1.5A piston-cylinder device, with a set of stops on the top, initially contains 3kg of air at 200kPa and 27°C. Heat is now transferred to the air, and the piston rises until it hits the stops, at which point the volume is twice the initial volume. More heat is transferred until the pressure inside the cylinder also doubles. Determine: 1.5.1 the work done; 1.5.2 the amount of heat transfer for this process. 1.5.3 Explain step-by-step the process from the moment that the heat is transferred to the air.

1.5A piston-cylinder device, with a set of stops on the top, initially contains 3kg of air at 200kPa and 27°C. Heat is now transferred to the air, and the piston rises until it hits the stops, at which point the volume is twice the initial volume. More heat is transferred until the pressure inside the cylinder also doubles. Determine: 1.5.1 the work done; 1.5.2 the amount of heat transfer for this process. 1.5.3 Explain step-by-step the process from the moment that the heat is transferred to the air.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5/ A piston–cylinder device with a set of stops initially contains 0.3 kg of steam at 1.0 MPa and 400°C. The location of the stops corresponds to 60 percent of the initial volume. Now the steam is cooled. Determine the compression work if the final state is (a) 1.0 MPa and 250°C and (b) 500 kPa. (c) Also determine the temperature at the final state in part (b).
An insulated vertical cylinder-piston device contains 0.8 m3 of refrigerant 134a at 1.2 MPa and 120 ° C. With a linear (compression) spring, all of its force is applied to the plunger at that moment. A valve connected to the cylinder opens and refrigerant escapes. The spring is loosened as the plunger is lowered, and the pressure and volume drop to 0.6 MPa and 0.5 m3, at the end of the process. Determine: a) the amount of refrigerant that escaped b) the final temperature of the coolant
A certain fluid expands in a quasi-static process from 0.4 m3 to 0.9 m3 at a constant pressure of 15 bar. The work done during the process is.
A water-jacketed air compressor handles 0.343 m3/s of air entering at 96.5 kPa and 21°C and leaving at 480 kPa and 132°C, 10.9 kg/h of cooling water enters the jacket at 15°C and leaves at 21°C. Determine the compressor brake power.
An insulated vertical cylinder-plunger device contains 0.8 m ^ 3of refrigerant 134a at 1.2 MPa and 120 ° C. With a linear (compression) spring, all of its force is applied to the plunger at that moment. A valve connected to the cylinder opens and refrigerant escapes. The spring is released as the plunger is lowered, and the pressure and volume drop to 0.6 MPa and 0.5 m ^ 3, at the end of the process.Determine:a) the amount of refrigerant that escaped andb) the final temperature of the coolant
Process of Ideal gasses 35m3 /min of air flows steadily through a compressor. It undergoes an isentropic change from 320C and 0.85 bar to 1.7 bar. The measured change in kinetic energy is 2.5kJ/kg. Neglect changes in potential energy and determine (a) the change in internal energy; (b) the compressor power requirement. A piston cylinder arrangement containing 2.2 kg of methane at 120kPa is heated at a constant temperature of 2400C. If during the nonflow process the heat transferred in kJ is numerically equal to half the final enthalpy, determine (a) the final pressure and volume; (b) the work
A piston-cylinder device initially contains CO2 at 200 kPa and 400°C and the total enclosed volume is 300 litres. Due to heat loss, the piston moves downwards to a position where it sits on a pair of stoppers and its final enclosed volume is 150 litres. Further heat loss leads to the pressure being reduced to 160kPa. Workout 1) the final temperature, 2) the total work done by CO2 and 3) the total heat transferred to CO2. Also make some comments on the result of heat. 4) Create a schematic p-v diagram of the process The following assumptions are to be made: CO2 is a perfect gas and its molecular mass is 44kg/kmol. The ratio of specific heat capacities, γ (gamma) is 1.3 The volume occupied by the stoppers is to be ignored. There is no leakage in the system There is no friction between the cylinder and piston walls and the piston moved slowly at the same speed therefore, no acceleration. For the conversion from Celsius to Kelvin, use 273 Use 8314.5 J/kmol.K for the universal gas constant
oxygen at 200 kPa, 27 degree celcius in a piston cylinder device arrange to maintain a constant pressure. how much work in KJ/kg is produced by this system when it is heated to 227 degree celcius?
Steam enters a nozzle with a low velocity at 150°C and 200 kPa, and leaves as a saturated vapor at 75 kPa. There is a heat transfer from the nozzle to the surroundings in the amount of 26 kJ for every kilogram of steam flowing through the nozzle. Determine the exit velocity of the steam.
Ten cu ft of air at 300 psia and 400F is cooled to 140F at constant volume. What are (a) the final pressure, (b) the work, (c) the change of internal energy, (d) the transferred heat, (e) the change of enthalpy, and (f) the change of entropy?
During an isothermal process, at 900F, the pressure on 9 lb of air drops from 85 psia to10 psig. For an internally reversible process,3.1 Determine the work nonflow3.2 Solve for the value of Q3.3 Determine ΔH
8 kg of water vapor are 2.8mpa and with 100 degrees celsius reject of 2180 kj/kg of steam at constant pressure determine enthalpy(kw), specific internal energy(kw),entropy(kj/K)