(#10) A 4-pole,3-phase, y-connected induction motor has 48 stator slots 8 series conductors per slot and coil pitch of 83.3 percent. (A) Determine the pitch and distribution factors. [Answer: 0.966 and 0.958] (B) Determine the maximum flux per'pole when connected to a' 220-volt,60-cycle line, neglecting local resistance and reactance drops. [Answer: 805,000 maxwells]

(#10) A 4-pole,3-phase, y-connected induction motor has 48 stator slots 8 series conductors per slot and coil pitch of 83.3 percent. (A) Determine the pitch and distribution factors. [Answer: 0.966 and 0.958] (B) Determine the maximum flux per'pole when connected to a' 220-volt,60-cycle line, neglecting local resistance and reactance drops. [Answer: 805,000 maxwells]

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.47P

See similar textbooks

Similar questions

Show the phasor diagram with the help of the equations you have created by drawing the exact equivalent circuit of the asynchronus machine. Please write clearly.
please explain steps-by-steps solution tq
Calculate the loop currents i1 and i2 Commentary:PLEASE, describe the procedure step by step, in detail. Do not do it on paper, digitally here :)
A stator impedance and equivalent rotor resistance of a 40 , 3-phase star-connected inductionmotor are (0.06 + j0.2) ohms and equivalent rotor impedance (0.06 + j0.2) ohms Neglect exciting current,Find the max gross power and the slip at which it occurs.
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.iii) Assuming that the post fault condition is small disturbance stable and that thereis no negative interaction among system controllers, calculate the criticalclearing angle, σcr, at which the fault should be cleared to ensure the generatorreaches a new steady…
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.
⦁ Does transformers work on DC? Justify your answer.
DEGREE: BS Electrical Engineering COURSE/SUBJECT: AC Machines NOTE: Please solve in this way. 1. GIVEN.(with symbols, if applicable) 2. ILLUSTRATION (If Applicable). 3. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and Detailed as possible. 4. Underline twice the FINAL ANSWER. PROBLEM: 5A three-phase, 3 KV, P=24, 50Hz, Y-connected slip ring IM has a rotor resistance of 0.015 ohm and a stand still reactance of 0.265 ohm per phase. Full load torque Is obtained al a speed of 245 rpm. Neglect stator impedance, Calculate (A) Ratio of Maximum Torque to Full load Torque (B) Speed at Maximum Torque
SUBJECT: Elements of Electrical Machines DesignINSTRUCTIONS: - Please write clearly and understandable way. - Write all the corresponding Given with their corresponding symbols and units. - Draw/Illustrate the diagram/circuit or drawings that is related to the problem, IF POSSIBLE, which is HIGHLY REQUIRED. - Solve in step-by-step, no shortcut - Underline twice the Final Answer.PROBLEM: In connecting ideal single-phase transformers in parallel, how will the load be shared if the two transformers have different VA rating?
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
The simultaneous equations representing the currents flowing in an unbalanced, three-phase, star connected, electrical network are as follows: 2.4I1 + 3.6I2 + 4.8I3 = 1.2 −3.9I1 + 1.3I2 − 6.5I3 = 2.6 1.7I1 + 11.9I2 + 8.5I3 = 0 Using Gaussian elimination, solve the equations for the currents.
It is a problem from Linear Systems Theory , chapter 2, Linearization i wanna detailed process for solving this problem. line by line