10. For the unity feedback system shown in Figure P7.1, where (Section: 7.3] 5000 G(s) = s(s+75) a. What is the expected percent overshoot for a unit step input? b. What is the settling time for a unit step input? c. What is the steady-state error for an input of Su(t)? d. Whatis the steady-state errorfor aninput of Stu(t)? c. What is the steady-state error for an input of 5r-u(t)? с. R(s) + E(s) C(s) G(s) FIGURE P7.1

10. For the unity feedback system shown in Figure P7.1, where (Section: 7.3] 5000 G(s) = s(s+75) a. What is the expected percent overshoot for a unit step input? b. What is the settling time for a unit step input? c. What is the steady-state error for an input of Su(t)? d. Whatis the steady-state errorfor aninput of Stu(t)? c. What is the steady-state error for an input of 5r-u(t)? с. R(s) + E(s) C(s) G(s) FIGURE P7.1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume any finite duration discrete time signal x(n) following the necessary condition satisfying the property of energy signal of your own choice. Now consider a discrete time system whichperforms Amplitude scaling operation followed by time reversal operation based on y(n) = ax(n) + x(-n). Sketch the output of resultant signal. Now classify and justify your answer with necessary and sufficient conditions that whether the above system based on all types of system.
a) What is the currenr flowing in the input resistor (i1) for t>0? b) What is the value of the feedback resistor Rf? c) What is the capacitor voltage in steady state (Vc( ∞ ))?
The control system manages, commands, directs, or regulates the behavior of other devices or systems using control loops. State the advantages of implementing negative feedback in a closed-loop system. Then Write the corresponding differential equation for the transfer function given, Specify the assumption made for the solution.
An op amp has a dc gain of 100 dB and a unity-gain frequency of 10 MHz. What is the upper-cutoff frequency of the op amp itself? If the op amp is used to build a noninverting ampliﬁer with a closed-loop gain of 60 dB, what is the bandwidth of the feedback ampliﬁer? Write an expression for the transfer function of the op amp. Write an expression for the transfer function of the noninverting ampliﬁer.
For the unity-feedback system with G(s) = K / s(s + 5)(s + 11): i. Find the gain K for the uncompensated system to operate with a 30% overshoot.ii. Find the peak time (Tp) and Kv for the uncompensated system.iii. Design a lag–lead compensator to decrease the peak time by a factor of 2, decrease the percent overshoot by a factor of 2, and improve the steady-state error by a factor of 30. Assume the lead compensator zero is at -5. Please specify all poles, zeros, and gains.
Ignoring the “zero” in the numerator, and based only on the denominator of the closed-looptransfer-function, determine the range of constants Kp and Ki such that the rise-time of theclosed-loop system is equal (or less than) ?r =0.18 s and so that the relative damping factor ζ isequal to (or greater than) 0.8. Use the textbook approximation for the rise-time.
Input signals that have high voltage noise that must be filtered cannot be immediately buffered because the buffer power supply voltages are often lower than the voltages present in the noise. With this in mind there are two circuits we have demonstrated that can work in this scenario. If you have a high impedance source, is it better to use an RC lowpass filter followed by a non-inverting amplifier, or to use an active lowpass filter design (both pictured below) and why?
what is the definition of overshoot, Decay ratio, rise time, and response time? I want the answer without Plagiarism.
Why do think the output voltage ?? resembles the input sinusoid?
An uncompensated unity feedback system with certain deficiencies has no zeroes and poles at -1, -2 and -5. Answer the following questions based on the above description of the system Determine using an apt technique, the gain of the system at damping ratio 0.45
In the feedback system given below; G1(s) = 5*K, G2 (s)= 1/s(s+4*4), H(s)= 1 given as time to settle down Ts ≤ 4 s and if the percent overshoot is Y*5 ≤ 5%, then what is the K value and damping ratio? For the K value you found above, the input signal r(t) is a unit step Calculate the steady state error.
Forward path transfer function in a unit feedback system is given as follows. What value should the K gain be to make the steady state error 37.3% ? (No matter which sign to apply)