A second order system has the uinty feedback and open loop TF 20 G(s) : S(S + 10) a) Find Damping ration and natural frequency values, 0, Wd,tr,tp,ts, Mp, Peak time for the system output when excited by unit step input ? b) Sketch the transient response for unit step input ? c) If input is ramp of 0.565 rad/sec calculate steady state error?

A second order system has the uinty feedback and open loop TF 20 G(s) : S(S + 10) a) Find Damping ration and natural frequency values, 0, Wd,tr,tp,ts, Mp, Peak time for the system output when excited by unit step input ? b) Sketch the transient response for unit step input ? c) If input is ramp of 0.565 rad/sec calculate steady state error?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the feedback system given below; G1(s) = 5*K, G2 (s)= 1/s(s+4*4), H(s)= 1 given as time to settle down Ts ≤ 4 s and if the percent overshoot is Y*5 ≤ 5%, then what is the K value and damping ratio? For the K value you found above, the input signal r(t) is a unit step Calculate the steady state error.
A differential amplifier connected in the circuitas shown has the parameters listed below withRI = 5 kohm and RL = 600ohm . (a) Find the overallvoltage gain Av, current gain Ai , and power gainAP for the amplifier, and express the results in dB.(b) What is the amplitude VI of the sinusoidal inputsignal needed to develop a 20-V peak-to-peaksignal at vo?Input resistance Rid = 1 M Output resistance Ro = 25 A = 60 dBvi = VI sin ωt
Ex. 1780. A closed-loop system has sustained oscillations (i.e. constant amplitude) with a period of 85 seconds when the gains are: proportional=96, integral=0, and derivative=0. Determine the ideal- PID gains Kp, Ki (minutes^-1), Kd (minutes) using the Ziegler-Nichols method. Also determine the standard-PID values which are commonly used in industry, such as LabVIEW: Kc, Ti (min), Td (min). ans:6
When the ltspice simulation of the circuit shown in the figure is performed, the output voltage (Vout) is obtained as given in which of the figures below? NOTE-1: Vcc = 12 V, RC = 2.2 kΩ, RB = 15 kΩ, RE = 180 Ω and C1 = 1 μF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.
Assume that the signal to be measured is displayed in the following form. y(t)=5sin1000t mV The time constant of the 1st order device is 100ms, K=1 V/V and its output is transferred to the 2nd order amplifier. The natural frequency and damping ratio of the amplifier is 15,000Hz and 0.8, respectively. Then, determine the expected output signal of y(t). And calculate the dynamic error and phase delay on the output. Is the chosen metrology system reasonable? If not, suggest a way.
Consider the unity-feedback system with the open loop transfer function: ?(?)= 1 /?+5 Obtain the steady-state output of the system when it is subjected to each of the following inputs: a- r(t) = sin(? + 30°) b- r(t) = 2cos(2? − 45°) c- r(t) = sin(? + 30°) + 2cos(2? − 45°)
Find the driving-point impedance ?(s) of the amplifier indicated in the diagram below in the ?S(s). Given Answer : ?(s) = Rin + 1/(sCin) = (1+(100π/s)) MΩ
Perhaps surprisingly, we can apply the transfer-function concept to mechanical systems. Suppose we have a mass m moving through a liquid with an applied force f and velocity v. The motion of the mass is described by the first-order differential equationf=m dv dt +kv in which k is the coefficient of viscous friction. Find an expression for the transfer functionH( f )= V F Also, find the half-power frequency (defined as the frequency at which the transfer function magnitude is 1/2 times its dc value) in terms of k and m.
a) What is the currenr flowing in the input resistor (i1) for t>0? b) What is the value of the feedback resistor Rf? c) What is the capacitor voltage in steady state (Vc( ∞ ))?
By plotting the locus-root curve of the open-loop transfer function G(s)= K / s (s+2); a) When K=4, show the locations of the closed loop poles on the root locus. Determine the damping ratio ζ and the natural frequency (wn) values at this gain value. b) Calculate and scale the unit step response of this closed-loop system by calculating the %overshoot, tp and ts (percent overshoot, peak and settling times, respectively). c) In order for this supervised system to work at least in the performance criteria (computed (greater than ζ and wn)) in question (a), scan the region where the pairs of conjugate poles should be located on the root-locus curve.
b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. c) Define the gain and phase margin, this time on the nyquist curve.
Given an inverting amplifier having a gain of 40 dB if the feedback capacitor is 10 pFDetermine the input and output Miller capacitance.Please show the complete solution