10/...find the shear stress in bolts51)80 kN80 kN8-bolt DIA. 10 MM80 kN80 kN8-bolt DIA. 10 MM110 MPa.127 MPa.509 MPano one O300 mm8 mm

It is required to determine the force on each bolt. P=ForceNumber of bolts=80 kN8=10 kN It is…

Answered: 10/.. find the shear stress in bolts 80…

Engineering

Civil Engineering

10/.. find the shear stress in bolts 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 300 mm 8mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Reqd: Determine Maximum Shearing Stresses for the 3 segments and Oat C (2)Solid 60-mm-diameter G =…

Q: Determine the Principle stresses at foint A using Mohris Circle. A 7,5m 1.5m 3 m 300 mm. 100m…

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

Q: The copper pipe [G = 5,000 ksi] has an outside diameter of 3.750 in. and a wall thickness of 0.250…

Q: The plate shown is fastened to the fixed member by seven 12-mm diameter rivets. Compute the polar…

A: The diameter of the bolt(d)=12 mm, The maximum shear stress(τmax)=75 Mpa Number of bolts(n)=7

Q: separate sheefs of paper. complete appropriate free-body diagrams. Problem 1: If the beam is made…

A: As per guidelines we need to answer only 1st question.

Q: The right-angle bar is supported by a pin at B and a roller at C. What is the maximum safe value of…

A: Given: The diameter of the pin is ¾ in. The shear stress is 20,000 psi. Consider the figure,

Q: EATWORK 2: The maximum shear stress allowed in Pin B is 70 MPa. Compute for the minimum diameter of…

Q: 1) Reqd: Determine Maximum Shearing Stresses for the 3 segments and 0at C 2) F (2)Solid…

Q: 1. The uniform 2-Mg bar is supported by a smooth wall at A and a pin at B that is in 10 m double…

A: Given data in question Weight of bar Pin in double shear Wirking shear stress To find out…

Q: 0,3in? 0.4in2 3P 2P + - 2P A Find the allbwable safe P if the stresses in the the following: AB = 50…

Q: The steel (Est = 200 GPa) shaft shown in composed of two hollow pipes AB and BC. The cross-…

A: Answer:- Given that:- Aab= 790 mm2 Abc= 350 mm2 Est= 200Gpa , ∆L=…

Q: Combined Loadings The bar is made of AISI 1006 cold-drawn steel and is loaded by forces F = 0.55 kN,…

A: Given data, F = 0.55 kN = 550 N P = 8 kN = 8000 N T = 30 Nm = 30000 Nmm d = 20 mm l = 100 mm

Q: Q5. Determine the resultant force on the Gusset Plate. -6 KN F-4 KN 888 888

A: Hi! Thank you for the question As per the honors code, We’ll answer the first question since the…

Q: What is the Shear Load on segment A-B? * O - 27 kips -25 kips -21 kips O -19 kips What is the Shear…

A: Given a beam with symmetric loading conditions Required: To find shear load on segment A-B…

Q: re welded to a rectangular web plate. Dimensions of the cross section are: = 430 mm = 16 mm = 110 mm…

Q: Find the max. shear stress at section а......а, T = (MPa) Ilomm 7KN 25 KN A 4. Hoomm 2m 2m 2m lomn-…

Q: normal Ja-25° K → P= AB kN

A: Given data: P=53 KNA=1200 mm2α=25o Calculating normal stress on the plane a-a:…

Q: 13-11. The staves or vertical members of the wooden tank are held together using semicircular hoops…

A: Draw the free body diagram.

Q: Q2:If allowable stresses are at = max. value of W. W 2m 8m 165MPa, oc = 100MPa t = 70MPa determine…

Q: A plate is fastened to a fixed member by four 20-mm diameter rivets arranged as shown. Compute the…

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

Q: or the beam shown, determine the stress in each rod if the load P= 50 kN is applied. Bronze Steel…

Q: A 2.5m long solid steel shaft is loaded as shown in the figure above. Using G = 83 GPa, determine…

Q: A horizontal beam AD is supported by an inclined strut CB carries a load W = 2.4KN at the position…

A: To determine: minimum bolt diameter at C stress in strut BC bolt stress at A Given, Load acting…

Q: Problem 12 A plate is fastened to a fixed member by four 16mmo rivets arranged as shown. Compute the…

A: Calculate maximum shearing stress?

Q: 2. Find the maximum tensile stress in the section of the beam and find the orientation of the…

A: This question is related to the Design Steel structures.

Q: Q9. For the post and loading determine the state of shown, 120 kN 50 mm 75 mm 50 mm combined…

A: Given:- P=120kN h=375mm To find:- state of combined stresses at point H and K

Q: Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as…

Q: 4. The plate is fastened to the fixed member using six ½ -in diameter rivets. Calculate the maximum…

A: Reinforced concrete : Reinforced concrete (RC), also known as reinforced cement concrete (RCC) and…

Q: 5. Determine the magnitude of the load P that will cause a maximum normal stress of max. o = 30 ksi…

Q: 225 of 207 225

Q: The average normal stresses developed in section a a of the turnbuckle, and the bolts shanks at B…

A: To find maximum value of load P

Q: A stepped steel (G=80 GPa) shaft (all solid rod) has the dimensions and is subjected to the torques…

A: torque in different portions of beam For ED torque TED=5 KN-m , dia D1=50mm and lengtht L1=0.5…

Q: X Your answer is incorrect. The copper pipe [G - 7,000 ksi] has an outside diameter of 3.250 in. and…

Q: he maximum allowable value of T considering the given maximum permissible angle of twist for the…

Q: Due Date: March 28, 2021 E If the load P on the beam causes the end C to be displaced 20 mm…

A: Strain is defined as the ratio of change in length to the original length. Mathematically,ε=∆lL…

Q: Q9. For the post and loading determine the state of shown, 120 kN 50 mm 75 mm 50 mm combined…

A: Area of cross section A=150×100=15000 mm2Axia force P=120 KNforce in Z direction…

Q: Determine the maximum average shear stress developed in each 12-mm-diameter bolt. 10 kN 5 kN 5 kN 0

Q: 50 kN 5kN/m В C D A I 70 kN - 3 m 5m +2m W200 x 19.3 Draw the shear-bending moment diagram of the…

Q: Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by…

A: As per bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: The average normal stresses developed in section a-a of the turnbuckle, and the bolt shanks at B and…

Q: A W 12 x 65 column section is 8 m long, pinned at each and has an additional support in the weak…

A: Given : W 12×65 column section.Total factored ultimate load, Pu = 1.2DL + 1.6LL K = 1.0 Properties…

Q: Q1. The rigid link is supported by a pin at A, a steel wire (E,) BC having an unstretched length of…

Q: Find the stresses in A, B and C? 7-d Vem 6m 0.006 MN o cm B -HA- 4m IX bem H

Q: m using area moment meth KN-m². W2 W1

Q: Problem Set #2 - FRICTION 6 cm MN Newton P=0.3 3 cm Required: 1. The minimum value of s if you…

Q: 1) Regd: Determine Maximum Shearing Stresses for the 3 segments and eat C 2) Re (2)Solid…

Q: 6O cm 20 20. 20cm 20 cm CnOSs - section 1. Determine the value the max Yalue g mament i 702 kN. cm…

Q: m-diameter rivefs. Assuming the axial load P = 90 kN is puted equally among the three =, find ne…

A: According to given Data Given that P= 90KNNow, A) Shear Stress in a rivet Ss=[P/As]…

Concept explainers

Planar Stresses

Question

10/...
find the shear stress in bolts
5
1)
80 kN
80 kN
8-bolt DIA. 10 MM
80 kN
80 kN
8-bolt DIA. 10 MM
110 MPa.
127 MPa.
509 MPa
no one O
300 mm
8 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
Determine the reactions at a and b for the beam subjected to the concentrated loads Ay= ? (Not 8.77 or 4.85 previous failed attempts on my behalf) bx = 7.2 Ax = ? (Not 1.9 or -.3365)
Is there possible solve support forces like this way of Ma :Ma= (10*2)-(19.5*6)+(3*4)*(7+4/2)-(3*11) Ma = -22KN-m
A W460×60 steel beam is loaded as shown. Assume w = 90 kN/m, M0 = 135 kN·m, LAB = 3.9 m, LBC = 1.6 m, E = 200 GPa, and I = 255 x 106 mm4. Determine the reaction force at roller B.
9 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 14B) 2C) 6D) 0E) 4
36 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, By=? a) 0B) 48C) 24D) NoneE) 14
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
d.) What is the location of the absolute maximum shear from the left end of the beam? (in m) e.) What is the absolute maximum moment in the beam? (in kNm) f.) What is the location of the absolute maximum moment from the left end of the beam? (in m) I'll re-post again the other questions. Same, imclude fbd.
What is the moment of the distributed load about the pin O? (a) 473 kN-m clockwise.(b) 338 kN-m clockwise.(c) 338 kN-m counterclockwise.(d) 270 kN-m counterclockwise.