100 A. If the motor developing half the torque. Choose the correct answer. Tal armature resistance is 0.1 ohm, and sh field resistance is 110 ohm. Assume th the magnetic circuit is saturated. 1- Armature current before the motor develop half torque is ? 2- Armature current after the motor de half torque is ? 3- Back e.m.f before the motor develop torque is? 4- Back e.m.f after the motor develop F

100 A. If the motor developing half the torque. Choose the correct answer. Tal armature resistance is 0.1 ohm, and sh field resistance is 110 ohm. Assume th the magnetic circuit is saturated. 1- Armature current before the motor develop half torque is ? 2- Armature current after the motor de half torque is ? 3- Back e.m.f before the motor develop torque is? 4- Back e.m.f after the motor develop F

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter52: Direct Drives And Pulley Drives

Section: Chapter Questions

Problem 8SQ

See similar textbooks

Similar questions

3) total Armature Winding resistance and shunt area winding resistance of a self-excitation DC shunt motor0.22 Ω and 170Ω respectively. Motor armature coefficient Ka = 40. DC shunt motor, a mechanical loadit operates at 230V for feeding and is powered by a full load current of 40A. Flux per polethe value is known to be 50mWb. Brush-contact voltage drop is 2V. Core losses andthe total loss of Rotary parts is 450W. Answer the following. (d) input power, copper losses, brush-contact losses and total loss power values in the enginecalculate. (e) calculate the efficiency of the engine. (Understand the formulas you use for calculations, the names of the relevant parameters, and your processing stageswrite it down somehow.)
3) The total Armature Winding resistance and shunt area winding resistance of a self-excitation DC shunt motor0.22 Ω and 170Ω respectively. Motor armature coefficient Ka = 40. DC shunt motor, a mechanical loadit operates at 230V for feeding and is powered by a full load current of 40A. Flux per polethe value is known to be 50mWb. Brush-contact voltage drop is 2V. Core losses andthe total loss of Rotary parts is 450W. Answer the following. (a) Armature current value (b) induced voltage value in Armature (c) the speed of the Motor,
The speed of a 230 V shunt motor is to be reduced from 900 r.p.m to 600 r.p.m. Theresistance of the armature circuit is 0.3 ohm. When the motor current is 30 A, speedis 900 r.p.m. If the current reduces to 20 A at lower speed, what arrangement shouldbe made? Neglect any effect not included in the data given. (Ans.3.833 ohms)
An 8-Pole, simplex lap wound, shunt generator has 800conductors and a flux per pole of 0.025Wb and running at 1200rpm. The armature and shunt field resistances are 0.25Ω and 120Ω respectively. If the armature voltage drop is equal to 10V, what is the load current (in Amp)? use two decimal places if the answer is not exact and do not include the unit anymore.
2. A four pole 2-Hp, 220-volts, 60-Hz, 3-Phase motorhas a delta connected stator and a Wye connected rotor.The ratio of which is 4:1. At full load, the slip is 2.5%. If the rotor resistanceper phase and the blockedrotor resistance and the blocked-rotor reactance are 0.3-ohm and 1-ohm respectively. Calculate d) Therotor power develop at full load and e) The rotor torque develop.
The speed of a 230 V shunt motor is to be reduced from 900 r.p.m to 600 r.p.m. The resistance of the armature circuit is 0.3 ohm. When the motor current is 30 A, speed is 900 r.p.m. If the current reduces to 20 A at lower speed, what arrangement should be made? Neglect any effect not included in the data given.
The armature winding resistance of a 200 Volt 4-pole DC motor is 2 ohms. Under full load, the armature current of the motor is up to 10 A. Armature coil is parallel wound and has 360 conductors. Since the magnetic flux under the pole foot of the motor is 12.5 mWb, which of the following is the motor speed? a 2100 rpm b. 2400 rpm C. 2500 rpm d.2300 d min
Identify the DC Motor used in Conveyor belt system. With a neat sketch explain its working. List it's advantages and disadvantages. - Reference must be added in slide. - Materials to be prepared apart from handout.
The no-load speed of a 240 V Dc shunt motor is 800 r/min and the armature current is 2A. Determine the resistance in series with the field so that the speed of the machine is increased to 950 r/min when the armature current is 30 A. The shunt circuit and armature resistances are 160 ohms and 0.4 ohm respectively. Assume the flux being directly proportional to the field current.
In shunt DC generator, the rated load power and speed are 6kW and 1500rpm. Therated load voltage is 230V. The internal armature resistance is 0.92Ω. The resistance ofthe field winding is 177Ω. Calculate the following:(a) The no -load voltage(b) Electromagnetic torque needed to start the generator armature in N-mHint: Use the formula PIN = (2π N T) / 60where PIN is the power inputN is the generator rated sped in rpmT is the torque needed to crank the generator armature in N-m(c) The percentage voltage regulator
A 500HP, 720rpm synchronous motor 3980V is connected with a 3-phase zone and excitation is 25A sample 1790 V (EA) voltage is produced in the armature. It has a synchronous reactance of 22 Ω and a torque of 30°. a) What is the voltage value falling on the synchronous reactance? b) What is the line current and power factor drawn by the motor from the mains? c) What is the power produced by the engine? d) What is the torque produced by the motor?
A 200V long-shunt generator delivers 100A, has an armature resistance of 0.05Ω, a series field resistance of 0.25Ω and a shunt field resistance of 200Ω. If a feeder resistance of 0.05Ω and a brush contact drop of 2.5V are considered, what will be the generated voltage (in Volts) of the machine? use two decimal places if the answer is not exact and do not include the unit anymore.