100 МPа 50 MPa 25 MPа 1) Sketch the Mohr's circle approximately to scale for the stress element. 2) Label the location of the three principal stresses. 3) Calculate the factor of safety based on the Maximum Shear Stress Failure Theory.

Q: 90 MPa 60 MPa 20 MPa

A: Given, Normal stress in x-direction = σx = -20 MPa Normal stress in y-direction = σy = 90 MPa Shear…

Q: 3. If o, = 30 ksi, o, = 20 ksi, and ty = 10 ksi, what is the maximum in-plane shear stress in ksi? →…

A: Given:σx=30 ksiσy=20 ksiζxy=10 ksi

Q: 10MPA For the state of plane stress. the and -40 MP Shown maximum minimum principal stresses are:…

A: Here, Stress in x direction = σx = 50 MPa Stress in y direction = σy = -10 MPa Shear stress in x-y…

Q: Homework: For the element shown find 1) Principle stresses and their direction 2) Shear stresses and…

A: (1) To find : The principle stress and their direction. Given data : The normal stress in X…

Q: The 175x100x16mm angle shown in the figure connected to a gusset plate with three 25mm dia. bolts…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: For the state of plane stress shown in Figure-1. t a) Draw Mohr's circle, b) Determine the maximum…

A: Given data:- σx=-20MPa,σy=90MPa,τxy=60MPa Center of mohr's circle=σx+σy2,0=-20+902,0=(35,0) Radius…

Q: 1. A point in a strained material is subjected to a tensile stress of 120 MPa and a clockwise shear…

A:

Q: Principal stresses:σ1=31.69 MPa σ2=−30.56 MPa Maximum in−plane stress: σmax=31.69 MPa

A:

Q: The maximum value of the torsional shear stress is kpsi.

A: To find Torsional shear stress

Q: A hollow steel shaft, 6 ft long, has an outer diameter of 3.07 in. and an inner diameter of 1.5 in.…

A:

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm.…

A: Inside diameter = 300 mm Inside radius = 150 mm outside radius = 260 mm internal pressure = 80 Mpa

Q: A 75mm shaft is subjected to 5KN-m torque. Find the stress developed in MPa.

A: Dear student, there are multiple question and we are suppose to solve only one question.  Also in…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: Estimate the normal stress (on) and shear stress (t) on the inclined plane as shown in the below…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: Thickness = 15 mm Find the stresses developed at point A 100 mm A ta 70 mm 180 mm 30 50 mm 500 N

A: Given: The thickness, t = 15 mm The width, b = 70 mm

Q: Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress=30…

A:

Q: Problem 1-5 The Cartesian components of stress at a point are given below : Oy = 5, Tyz = - 4,…

A:

Q: 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the a

A:

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…

A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy…

A: Given Dataσs=150MPaFy=250MPat=20mmw=300mmσt=0.6Fy=150MPa

Q: A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under…

A: Calculate the strain in the wire. ε=δll Here, l is the original length of the wire, δl is the change…

Q: Q.1) For the given state of stress at a point (Normal stresses are 200 & 150 MPa, and Shear stress…

A: Given data:6x=-200MPa6y=-150MPa      → compressive normal stressτxy=100MPaθ=30°To find:1) Normal…

Q: 500 MPa and 200 MPa, respectively, then the factor of safety for the shaft is

A: Given data; Max. bending stress=100 Mpa Strength of the shaft material 300 Mpa,500 Mpa and 200Mpa…

Q: In a biaxial state of stress, normal stress are 900 N/mm^2 and 100 N/mm^3 in x and y diretion…

A: Given data σx=900 MPaσy=100 MPaτxy=300 MPa

Q: If the principle stresses in a plane stress problem are 100 MPa and 40 MPa, then maximum shear…

A: As given in the question, Maximum principal stress = σ1 = 100 MPa Minimum principal stress = σ2 = 40…

Q: 8. Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

A:

Q: 1. Calculate the maximum stresses to occur in the hole and groove (groove) areas in the plate below,…

A: Given, Applied load (F)=5000N Width of the plate=200mm The thickness of the plate (t)= 25mm Diameter…

Q: is shown below, 400 300 200 100 Stress (MPa)

A: 1.Modulus of elasticity can be obtained by taking the slope of stress-strain curve in elstic…

Q: 2. A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is…

A: Given data:

Q: 3MP 8MPd 45 2MPA Determine the two principal stresses in MPd

A:

Q: 3. For the given state of stress, determine the principal planes, the principal stresses, and…

A:

Q: Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

A: We are restricted to solve one question at a time. Please ask other questions in the next post.…

Q: 26. If ơ, = 50 ksi, oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…

A: Given: The stress along x-axis, σx = 50 ksi The stress along y-axis, σy = 10 ksi The shear stress,…

Q: A steel punch having diameter 10 mm is used to make hole in a 2.5cm thick steel plate. What will be…

A:

Q: 1 MPа 2- For the state of stress as shown below, 2 МPа a) Find principal stresses З МРа b) Draw…

A:

Q: For the element shown find 1) Principle stresses and their direction 2) Shear stresses and their…

A:

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: Given data  diameter of shaft (d) = 80 mm  maximum shear stress in shaft (τmax) = 63 MPa width of…

Q: The principal stresses at a critical point in plane stress are o and 0.250. The yield stress for the…

A:

Q: Draw the Mohr's Circle (Fig. 3) as accurately as possible on a graph paper. (a) Using equation find…

A:

Q: A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa,…

A: GivenN=400rpmP=10kWσa=40MPa

Q: For the following state of stress, 48 MPa 16 MPa 60 MPa Find: i. The principal planes ii. The…

A: Given data: σx=16 MPaσy=-48 MPaτxy=60 MPa Need to determine the principal plane, principal stress,…

Q: Calculate the normal stress and shear stress acting on the plane 2x+y+2z=1 passing thorough a point…

A: given; plane ;2x+y+2z=1stress at point (σ)=162022000023

Q: 1. If o, = 20 ksi, o, = 10 ksi, and txy = 30 ksi, what is the absolute maximum shear stress for the…

A: Calculated absolute maximum shear stress.

Q: Q2) Look at the Mohr Circle and find (the scale is 1 cm-10 MPa) 1. Normal and shear stress at points…

A: Since we only solve upto three subparts at a time, we will solve the first three. Please specify the…

Q: A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under…

A: Given: Young's modulus (E)=8.5×106N/m2Original length (L)=1.5mElongation (δ)=2.5mm or 0.0025m

Q: Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

A: Punching is a process is used to make holes in the sheet metal by forcing a tool which is called a…

Q: hear stress element. Any stress components not shown are assumed to be zero. Work problem #4

A: Part A) First, draw the coordinate system and depict the given point in the below expression.