For the given stress element, consider the magnitude for oA, OB, and t to be 15.0 MPa, 40.0 MPa, and 40.0 MPa, respectively. 12

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11633 N force. - 540…

A: P= 11633 N Width of the cross section, b= 60 mm Height of the cross section, h= 180 mm

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: 3. If o, = 30 ksi, o, = 20 ksi, and ty = 10 ksi, what is the maximum in-plane shear stress in ksi? →…

A: Given:σx=30 ksiσy=20 ksiζxy=10 ksi

Q: The point on the surface of the pressure vessel in Fig.a is subjected to the state of plane stress.…

A: Given data: The maximum principal stress acting on the point of the pressure vessel is σ1 =16 MPa…

Q: The beam is supported by two rods AB and CD that have cross- sectional areas of 13 mm² and 7.8 mm²,…

A:

Q: For each of the elements shown below, draw Mohr's circle and determine the principal stresses (0₁,…

A:

Q: The system is initially unstressed but the right support is moved 3 mm to the right whereas the left…

A:

Q: 100 MPa 75 MPa 150 MPa

A:

Q: A cylinder having an internal diameter of 20 in and an external diameter of 36 in is subjected to an…

A:

Q: The state of plane stress at a point on the surface of the airplane fuselage isrepresented on the…

A:

Q: Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2

A: Given data: Tensile force (F) = 20 N Cross sectional area (A) = 5 mm2 Need to determine the stress…

Q: Draw Mohr’s circle that describes each of the following states of stress.

A: The Mohr circle diagram for the respective figures are as follows:

Q: mounted on a 2-inch shaft as shown transmits 9 kW at 1000 rpm. What is

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A:

Q: For the state of plane stress shown in Fig. (a), determine the maximum in-plane shear stress and the…

A: (a) The maximum in-plane shear stress: 15 ksi  (b) The absolute maximum shear stress: 25 ksi

Q: What is the magnitude of the having a radius of curvature o tensile stress of 140 MPa is ar 4.

A: 4. Given              Normal stress = 140 MPa            Crack length, a = 3.8 x 10-2 mm Radius of…

Q: 30 mm and 40 mm, respectively. Determine the principal stresses and

A:

Q: - 540 mm 180 mm- 180 mm 60 mm → - B 30 kN

A:

Q: The state of stress at a point is shown on the element. Determine (a) the principal stress and (b)…

A:

Q: Determine the maximum and minimum stress intensities set

A:

Q: 8. 10 plate 8X10 - S00 pounds of loud material 6061 Aluminum - Determine what type of stress Is…

A: Hf

Q: 4) The state of plane stress at a point is described by Or = Oy = o and Tæy =0. The stress on the…

A: given data  σx = σy = σ, ζxy = 0  to determine stress on the plane inclines at 45 to x plane

Q: For the state of plane stress shown below, determine the principal stresses, the maximum in plane…

A:

Q: Determine magnitude of the stresses acting on plane inclined at an angle 0 = 30°, where the vertical…

A:

Q: Determine stress distributions, Ox, Oy and txy

A: we will first determine the load function , the the bending moment and hence the stress distribution

Q: choose the correct answer Mcq: the maximum shar stress in contact between two steel spheres pressed…

A: Option one is correct. At the contact surface

Q: Determine magnitude of the stresses acting on plane inclined at an angle 0 = 30°, where the vertical…

A:

Q: A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The…

A:

Q: 4.0 kPa is used to carry a 3.5 m3of water has a height of 2.0 m and thickness of 5.0 mm. Determine…

A: given:V=3.5m3h=2mt=5mmP=114KPa

Q: Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated…

A: Given data: The diameter of the segment at A, dA = 0.5 in. The diameter of the segment at B, dB = 1…

Q: Determine the equivalent state of stress if an element is oriented 20° clockwise from the element…

A:

Q: the normal stress using Mohr's circle

A: Given:  X = 7 ksi and Y = 35 ksi To determine: The normal stress using Mohr's circle

Q: Calculate the average normal stress and determine the radius of Mohr's Circle. Then draw Mohr's…

A: Write the given data in the problem.   Sx=-36 MPa  Sy=-70 MPaSxy=25 MPa Here, the negative sign on…

Q: Determine the equivalent state of stress on an element at the same point oriented 60°…

A: Given Data: The value of σx=150 MPa The value of σy=100 MPa The value of τxy=75 MPa The orientation…

Q: 1. For the state of plane stress with x-y axes as shown, do the following: 12 MPa 1.1 draw the…

A:

Q: Use 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively.…

A: To find stress in member CD

Q: A cylindrical pressure vessel is fabricated from steel plating that has a wall thickness of 15 mm,…

A: Wite the expression for the longitudinal stress (axial stress)

Q: Calculate the stress parallel to the inclined plane AB. Report your answer as a positive number.…

A:

Q: A pressure vessel containing gas at 250 psi has an outer diameter of 12 inches and a thickness of…

A:

Q: ROKNE 20KN 50m2

A:

Q: A cylinder having an internal diameter of 20 inches and external diameter of 28 inches is subjected…

A: di = internal diameter = 20 in do = external diameter = 28 in pi = internal pressure =8500 in σho =…

Q: Determine the factor of safety as per tresca's max shear stress theory

A: Given: A machine element is subjected to the following bi-axial state of stress:σx=80 MPaσy=20…

Q: Determine the equivalent state of stress if an element is oriented 20° clockwise from the element…

A:

Q: Q2) Determine the normal stress at points A and B. Also, calculate how much the neutral axis is…

A:

Q: Given sigma x=100 MPa, tau xy=50 MPa, determine stresses at an angle 30 degrees CW from x-axis.

A:

Q: * 'Determine the ox 30 MPa 10 MPa 20 MPa The state of plane stress at a point is represented on the…

A: find the segma x in oriented element.

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.