12 in Problem #7, Please only do 1.52 1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a x-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is con nected to its support at B by a f-in.-diameter pin; all of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.25 is desired, determine the largest load P that may be applied at D. Note that link AC is not reinforced around the pin holes 1.52 Solve Prob. 1.51, assuming that the structure has been redesigned -in.-diameter pins at A and C as well as at B and that no other change has been made. to use in. 8 in Г 6 in 4 in

12 in Problem #7, Please only do 1.52 1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a x-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is con nected to its support at B by a f-in.-diameter pin; all of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.25 is desired, determine the largest load P that may be applied at D. Note that link AC is not reinforced around the pin holes 1.52 Solve Prob. 1.51, assuming that the structure has been redesigned -in.-diameter pins at A and C as well as at B and that no other change has been made. to use in. 8 in Г 6 in 4 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Identify the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m. Kindly give me the solution of this please.
Frame ACGE is on hinge support at Aand E and braced at B and F to resistforce T = 18kN.a = 2 mb = 1 mc = 1 ma. Find the reaction at D in kN. b. Find the stress in brace BD if it ismade of pipe of ø = 75 mm andthickness = 6 mm. c. If brace AB is connected to BDconsist of two flat bars bolted topost AC at B using 20-mm-ø bolt,find the average shear stress (inMPa) in the bolt.
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
d.) What is the location of the absolute maximum shear from the left end of the beam? (in m) e.) What is the absolute maximum moment in the beam? (in kNm) f.) What is the location of the absolute maximum moment from the left end of the beam? (in m) I'll re-post again the other questions. Same, imclude fbd.
Give me the solution. Question: Identify the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m
the bridge truss shown is to be subjected to moving loads. L= 8m, P=0kN, theta = 50°
Q: Find the axial force at member CD(FCD). -EA=1000t (all members)
Find the max tension on member DI in kN. Put "0" if none. a= 4.5m b= 4.8m c= 50kN d= 68kN
BADLY NEED IN 1HOUR PLS THANKYOU Above is a simple truss with P = 45.67 KN (write answers in kN in 2 decimals) Compute for the forces in: a. Member DA b. Member BH c. Member HI d. Member DG e. Member El f. Member AF g. Resultant Force Reaction of Support F (3 pts)
pls answer a, b ,c and highlight the answer A 5.50m beam (425mm by 525mm) is fixed support on one side and roller support on the other side carries a uniform load all throughout its length. It is reinforced with 4D20mm (tension) and two D16mm (compression). Taking fc’=33MPa, fy=415MPa, clear cover=40mm and dv=10mm. a. Determine the balanced moment, kN-m. b. Determine the maximum moment assuming using the NSCP 2015. c. Determine the superimposed dead load it can carry if the beam carries a live load of 20kN-m.
The cables AC and BC supports a load W with L= 20m a. If x1 = 7m and d= 2m what is the normal stress at both cables when loaded with W=60kN with cables’cross sectional area is 20mm2
Instruction: Follow Given-Required-Solution format for your computation. Complete FBD for full credit. Problem: Neglecting the weights of the members, determine the magnitude of the pin reaction at D when the frame is loaded by the 200-N.m couple.