12 kip -20-/ y х 30 in. 12 kip

Q: A composite bar as shown in Fig 3 is firmly attached to unyielding supports at the ends and is…

A:

Q: A circular metal column is to support load of 500 Tonne and it must not compress more than 0.1 mm.…

A:

Q: A round steel tension member 40 in. long is subjected to a maximum load of 6,500 lbf. (a) What…

A: Given:- Length : 40 in Load : 6500 lb

Q: QUESTION 3 A 300mm x 100mm channel section is used as a short vertical column. The column is to…

A: given; →dimension ; (b*d)=300mm*100mm→width(b)=300mm→depth(d)=100mm→compressive load (P)=500KN…

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A: Given that, Radius of gyration of column, k=150 mm,Cross-section area, A=0.02 m2Modulus of…

Q: 8- A coper road is inserted into a hollow aluminum cylinder . The copper rod projects 0.130 mm as…

A:

Q: os. A mild steel strut is of single angle section 100 mm x 75 mm x 8 mm. Its length is 3m with both…

A: Strut is a member or bar (in any position), which is subjected to axial compressive load. Column is…

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A:

Q: H.W: 1 rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the…

A:

Q: 1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50kN.…

A:

Q: The pin-connected structure consists of two cold-rolled steel [E = 28,000 ksi] bars (1) and a bronze…

A:

Q: The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.31 in2. Find the…

A: Answer: The vertical displacement of point C is 0.0921 inches.

Q: A column is made from a rectangular bar whose cross section is 5.1 cm by 8.7 cm If the height of the…

A:

Q: A steel plate subjected to a force of 3 kN and fixed to a vertical channel by means of four…

A: Given data: Force F=3 kN Yield Strength Syt=380Nmm2 Factor of safety FOS=2 Diameter of shank d=?

Q: 1.2 Figure 1 show a compound bar made of the aluminum alloy with three different cross sectional.…

A: Given: Compound bar made of aluminum alloy with three different cross section , A load is applied…

Q: Compute for the total elongation caused by an axial load of MN kN applied to a bar 20 mm thick…

A:

Q: An airplane’s landing gear must be capable of supporting ⅓ of its weight at 200000 kg. To induce…

A:

Q: ick as shown in the ield strength of the 260 N/mm², and plastic moment of nape factor.

A:

Q: The W8 x 15 wide-flange A-36 steel column is assumed to be fixed at its top and bottom (Figure 1).…

A: Write the properties of the W8 X 15 flange. Write the values of the properties of A-36 steel.

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A:

Q: A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the…

A: Given: Length of the cast iron is 3m. External diameter of the tube is 450mm (misprinted). Thickness…

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A: Area, A = 0.02 m2              E = 200 GPa  Length, L =6 m Find    Load, P    Stress…

Q: At the proportional limit, a 22 mm thick 75 mm wide bar elongates 6.3 mm under an axial load of 482…

A:

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A: Given:Radius of gyration of column, r=150 mmcross-sectional area, A=0.02 m2E=200 GPaσ=275 MPaLength…

Q: in A Composite bar Çansists af QI) an aluminum Section rigidly fastened between as shown in fiqure…

A:

Q: 8-13. A structural member in a nuclear reactor is made of a zirconium alloy. If an axial load of 20…

A: Given, E = 100 GPa  σY = 400 MPa P = 20 kN The factor of safety = 3 Length (L) = 1 m Factor of…

Q: A steel pipe having the cross section shown is used as a column. Use oy= 250 MPa, t= 6.3 mm, FOS =…

A:

Q: composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy…

A:

Q: Determine the maximum axial load P (in kN) that can be applied to the wood compression block shown…

A:

Q: An axial load of 38.7 kN is applied to the circular member as shown. The length of the member is 15…

A: This is the very basic question of strength of material and the elongation due to axial load is the…

Q: A gazebo is planned to be constructed in a community park as an additional shelter for visitors from…

A: Solution: Given Data: A=7200 mm2SR=0.026E=200 GPaσy=233 MPaFOS=1.67K=0.7 (for Fixed-pinned end)

Q: Ieng In an aircraft structure, a rod is designed to be 1.25 m long and have a square cross section…

A: Given data for aircraft structure,

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy…

A:

Q: A vertical steel rod is fixed at the top and supports an 8-kN load at the lower end. The rod is 10…

A: Given data-rod diameter=10mmlength=25mmweight of steel=77 kN/m3

Q: The rnigid bar of weight W= 100 KN is carried by three rods as shown. The mechanism is arranged such…

A: Given data as per the question Increase in temperature =800 c Length of steel bar =1 m Length of…

Q: A cylindrical rod of diameter 23 mm and length 234 mm is subjected to a tensile load of 57 kN and it…

A:

Q: Determine the maximum axial load P (in kN) that can be applied to the wood compression block shown…

A: Givenτa=4.59MPaθ=60oL=320mmd=120mmw=200mm '

Q: (A). A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm…

A: The area of the bar AB is AB=a2=252=625 mm2 The area of the BC is BC=π4d2=π4202=314.15 mm2 The area…

Q: The steel bar has the original dimensions shown in the figure. It is subjected to an axial load of…

A: When a bar is given tensile stress it tends to get elongated longitudinally, called the longitudinal…

Q: A wide flange A60 steel column has a length of 4.5meters and pinned ends. If Sx=898x103 mm3,…

A: Calculate the moment of inertia along x, y direction Ix = Sx*(d/2) = 898*103*(358/2) =1.6* 108   mm4…

Q: 2. A core made of stainless steel (material 1, E, = 28 Msi) is fully bonded to an inner shell of…

A:

Q: answer as soon as possible

A: Write the given information. Write the expression of expansion of rod due to free expansion due to…

Q: A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of 200kN.…

A:

Q: Consider a deformable homogenous slender rod of constant area along its length. It is axially loaded…

A:

Q: 2. A 45-cm long rod of 1020 grade steel will be used as a frame support. It will be subjected to a…

A:

Q: A column of length 1 m is hinged at both ends has cross-section (10 x20) mm2. Young's modulus of…

A: Given data:Length of the column, L=1 mCross-section of column, A=10×20 mm2E=200 GPa

Q: 9- Compute the total elongation caused by an axial load of 100 kN applied to a flat bar 20 mm thick…

A: Find the total elongation caused by an axial load 100 KN applied to a flat bar 20 mm thick ,…

Q: A hollow circular column of 200 mm external and 160 mm internal diameter is subject to an axial…

A: given data; external diameter(d1)=200mminternal diameter(d2)=160mmcompressive load…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.