12. 120v + Vi b) a -12ov rideal

Q: The power Transmission line is a three-phase supply. Select one: True O False

A: The power transmission line is used to transmit the electrical energy from generating source/plants…

Q: 6. Three inductive loads each of resistance 750 and inductance 318.4mH are connected in delta to a…

A: Given, Resistance per phase (Rph)= 75 ohm Inductance per phase (Lph)=318.4 mH Line voltage (VL)= 415…

Q: A 3 φ delta connected load when supplied from 430V, 50 Hz source takes a line current of 8 A…

A:

Q: Q/2/Determine the input impedance (ZT) and current (IT) of the series network consist of (R = 50, X₁…

A: In this question,  We need to determine the equivalent impedance ZT  and total current IT   Also…

Q: A 3-phase 415, 50Hz supply is given to delta connected load with impedance (6+j14) ohms. The line…

A:

Q: (a) Determine the Norton equiv

A:

Q: In a 3-phase delta connected system, prove that IL =V/3 Iph by considering the line current (11 = IR…

A: The detailed solution is provided below.

Q: A short 3-phase transmission line connected to a 33KV, 50 Hz generating station at the sending en…

A: The solution can be achieved as follows.

Q: (4+/6)12 (104j12)12

A:

Q: 1.Draw the Thevenan equivalent circuit for terminal a-b.   2.Find the value of impedance ZL that…

A:

Q: A three-phase overhead transmission line delivers 500kW at 33kV.The current flowing through the…

A: Cos of angle between voltage and current is power factor .

Q: 18. A network has a total impedance of Zr = 24.0 kn/-30° at a frequency of 2 kHz. If the network…

A:

Q: 12.18 If Van 220/60° V in the network of Fig. 12.49, find the load phase currents IAB, IBC, and ICA-…

A: The given voltage Van=220∠60° V The expression for the line voltage is,…

Q: For the circuit shown in figure 1, calculate the equivalent impedance of the network, assuming a…

A:

Q: The phaser form of v=123cos(50t-30)= 123 /-30 True False

A: We need to find out the phasor of given signal

Q: 5445°A a I: I3 -j2n I2 j2n 1223OV j20 all For the following ac networks, determine, using the…

A:

Q: A balanced 3-phase load of 30 MW is supplied at 132.1 kV and 0.85 pf lagging by means of…

A: From the General expression of Percentage voltage Regulation

Q: Q1/ For the circuit shown below, determine the value of Vo, using Nodal analysis. 30 ww- 60 ww

A: The solution can be achieved as follows.

Q: The half-controlled single-phase bridge circuit is supplied at 120 V. Neglecting volt-drops. If the…

A: In this question,   We need to choose the correct options What is required device rating if bridge…

Q: Find the line and phase voltage if Vcn= 30<50 V. Assuming ACB sequence

A:

Q: A 100 km long three phase transmission line has resistance 12Ω per phase, inductance per phase 0.15…

A:

Q: Find voltage Va  Vb  and Vc  using nodal analysis

A: In this question we will find node voltages...

Q: A three phase distribution board of installed power 50KVA is supplied at 220/380V with a demand…

A:

Q: Q1. A lossless T-junction power divider has a source impedance of 50 Ohm. Find the output…

A: Given: A lossless T-junction power divider has a source impedance of 50 Ohm. To find: Find the…

Q: 12.57 Determine the line currents of the three-phase circuit in the figure. /-120°, V. = 110/120° V.…

A: The solution can be achieved as follows.

Q: = 7200 ∠ - 130 ° V VBN = 7200∠110 ° V? Also, find VCN

A: The sequence components are equal in magnitude and displaced by 120 degree. The angle between the…

Q: 1.Draw the Thevenan equivalent circuit for terminal a-b. 2.Find the value of impedance ZL that must…

A:

Q: For the following ac networks, determine, using the superposition theorem, the indicated currents.…

A: Note: We are authorized to answer one question at a time since you have not mentioned which question…

Q: O Hz, three phase 50 km transmission line delivers 13.5 MW of power to a load at 19.052 kV phase…

A: In this question , we will find sending end voltage and regulation..

Q: In a two-wire distributor ABC, C passes a load of 120 A and B passes 60 A and both have a lagging…

A:

Q: For the given circuit calculate the maximum power that can be transferred from the circuit to the…

A:

Q: Load impedance, ZZLL = 150 − jj70Ω is to be matched to a 50Ω line using a single series stub tuner.…

A: Given: ZL=RL+jXL=150-70j Ω Z0=50Ω

Q: If three Impedances each of (8-j 6) N are connected in mesh across a three-phase 400 V ac supply,…

A:

Q: Q13. The input voltage wavef orm of single phase bridge is having only DCcomponent. O True O False

A: The input voltage waveform of single phase bridge is having only DC component?

Q: In a 3-phase delta connected system, prove that L =/3 Iph by considering the line current (I1 = IR -…

A: Let's assume a 3 phase balance Delta load.  Prove that line current iL  = √3 iph  for Delta…

Q: Solve the total impedance of the circuit if R= 40 ohms , XL=150 ohms, XC= 120 ohms , V= 100 volts

A: Given circuit having, R = 40 ohms XL =150 ohms XC = 120 ohms

Q: Q2: Design open-circuit parallel single stub near to the load to match load impedance of ZL = 80 +j…

A: Here is your answer! I hope this will help you.

Q: A balanced 3-phase load of 30 MW is supplied at 142.4 kV and 0.85 pf lagging by means of…

A: Given full load receiving end voltage Vfl = 142.4 KV and sending end voltage = 141 KV line constant…

Q: A single-phase distributor AB has a total impedance 0f (0.1+j0.2) ohms. At the far end B, a current…

A: we need to determine the sending end voltage.

Q: 3/ Find the impedance parameters for the network shown below V₁ 125 Ω 50 Ω 75 ΩΙ V₂

A: Given circuit :

Q: 52 For the coupled circuit shown if Vs=30Z0°V: 1. Calculate the total impedance between 22 42…

A:

Q: For the given circuit calculate the maximum power that can be transferred from the circuit to the…

A: In this given circuit,  Find the maximum power transfer to the load.  For maximum power transfer…

Q: In a 3-phase delta connected system, prove that IL =V3 Iph by considering the line current (I1 = IR…

A: In this question we need to prove that for delta connected system, IL=√3 Iph

Q: Given a mesh connected system with reactive factor of 60 percent, true power of 2,500 kW and phase…

A: A network in which devices or nodes are linked together, branching off other devices or nodes known…

Q: For the network of the next picture: a. Determine the total impedance ZT. b. Calculate the voltage…

A:

Q: A balanced 3-phase load of 30 MW is supplied at 136.6 kV and 0.85 pf lagging by means of…

A:

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.