A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end isrequired to supply a load of 10 MW at 0-8 lagging power factor at 30 kV at the receiving end. If theminimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance andinductance of the line.[2-4 Q; 0-028 H]c001-

A short 3-phase transmission line connected to a 33KV, 50 Hz generating station at the sending en required to supply a load of 10 MW at 0-8 lagging power factor at 30 kV at the receiving end. If minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance inductance of the line. [2-4 Q; 0-028

A short 3-phase transmission line connected to a 33KV, 50 Hz generating station at the sending en required to supply a load of 10 MW at 0-8 lagging power factor at 30 kV at the receiving end. If minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance inductance of the line. [2-4 Q; 0-028

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

A 3-ph, 60 Hz, 200 km long, 220 kV transmission line has per km per phase constants of resistance 0.033 Ω, inductive reactance 0.33 Ω, capacitive susceptance 3.3x10 -6 mho. The load at the receiving end of the line is 500 MW at 0.95 power factor leading and voltage has dropped to 209 kV. Using the PI model, calculate the voltage, current and power factor at the sending end. Please answer in typing format solution please only typing format Please I will like it please reply to
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
A 30 mile, 3-phase transmission line delivers 8,000 kW at 33 kV, p.f. 0.8 lagging. The resistance and reactance of single conductor are 0.6 ohm and 0.72 ohm respectively per mile. Find the voltage at the sending end in kV.
A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10 MW at 0.8 lagging power factor at 30 kV at the receiving end. If the minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance and inductance of the line.
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
electrical engg .fig.shows a single-line diagram of a power system where the generator is connected to the bus 1 and the load is connected to the bus 2. The line impedance is 0.12 +j 0.23 pu on a 100 MVA a base. Per unit real power and reactive power supplied to the load are 0.50 and 0.30 respectively. Bus 1 is a slack bus. Use Gauss-Seidel method to determine the (i) voltage at bus 2, (ii) slack bus real and reactive powers, (iii) line flows,
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line
An energy transmission line with a length of 130 km transmits 150MVA of power at 380 kV voltage. The conductors used have a conductivity of 35 [m / mm mm²] and a diameter of 28.11mm. The final temperature reached by this transmission line is 66 degrees. (NOTE = temperature coefficient of conductor a20deg = 0.00403deg ^ -1) Approximately how many kWatts is the total loss in the three-phase line at 20 degrees?
A 220 kV, 50 Hz, three-phase transmission line is 60 km long. The resistance per phase is 0.15 ohms/km and the inductance per phase is 1.3 mH per km and the shunt capacitance is negligible. Use the short line model to determine; i) the voltage and power at the sending end ii) voltage regulation and efficiency when the line is supplying a three-phase load of 350 MVA, 220 kV at a power factor of 0.85 lagging.
1/In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase transmission line, 60HZ, have: (50 MW, 0.866 lagging p.f. and 132 kv in receiving end. If the line have (Z = 100 <80 Ohm / phase and Y = 0.0012 <90 S). Calculate: Vs, Is, Vreg, and power factor in sending end. Also, find the transmission efficiency? For the following transmission models: 1- Short transmission line model. 2- Medium transmission line (pi) model. 3- Medium transmission line (T) model. 4- Long transmission line model. (Please show your answer steps)
A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10 MW at 0·8 lagging power factor at 30 kV at the receiving end. If the minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance and inductance of the line. [2·4 Ω; 0·028 H]