12. A beaker of height 15 cm is partially filled with a liquid and is rotated by an angle 0 as shown. If the pressure at point B becomes 5 bar, what will be the value of 0? A 15 cm B а) 30° b) 50° c) 60° d) 70°

12. A beaker of height 15 cm is partially filled with a liquid and is rotated by an angle 0 as shown. If the pressure at point B becomes 5 bar, what will be the value of 0? A 15 cm B а) 30° b) 50° c) 60° d) 70°

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter3: Natural Soil Deposits And Subsoil Exploration

Section: Chapter Questions

Problem 3.1P

See similar textbooks

Related questions

Q: A closed cylindrical tank, 6 feet in diameter and 12 feet high contains water to a depth of 10 feet.…

A: The values given in the question are as follows: Diameter of the tank(D)=6 ft Height of tank(H)=12…

Q: A water jet is deflected 30° by a stationary vane as shown. The incoming jet has a speed of 40 m/s…

Q: an open cylindrical tank 45 cm in diameter and 135 cm tall is full of water and revolved about its…

A: Given Data: Given Data:Diameter of the tank (d) = 45cm = 0.45mheight of tank (z) = 135cm =…

Q: SITUATION: An open cylindrical vessel 1.3 m in diameter and 2.1 m high is 2/3 full of water. If…

Q: A manometer is used to measure the pressure in a tank filled with air. The fluid has a specific…

A: given atmospheric pressure = 96 kPa S.G= 0.95 ρw=1000 kg /m3 h=65 cm=0.65 m Gauge…

Q: b ▼ 2m 2m 2m 15m a

A: Given:- Coefficient of friction=0.60γconcrete=23.5a=28 mb=25 m Different types of forces acts on a…

Q: If we compress water by applying 20433.5 Mpa pressure, how much volume change can be observed?. Bulk…

Q: 2. A hemispherical bowl having a radius of 1 m is full of water. If the hemispherical bowl is made…

Q: How high will liquid rise in the piezometers of shown in the figure if the pressure at M is liquid…

A: Given data in question Pressure at point M Specific gravity To find out Height h Note Acceleration…

Q: A water jet strikes a rectangular block through a cavity, as shown in Fig.2, and deflected back at…

A: step 1-

Q: In the figure below, a block is sliding down over a liquid film. Calculate the average pressure (in…

A: Data Given: W = 11 Nθ = 33°A = 0.20 m2 Asked: Average Pressure

Q: Shown in the figure below is a small decorative wheel fitted with flat paddles so the wheel turns…

A: The diameter of the stream is d=15 mm. The velocity of the stream is v=0.35 m/s. The density of the…

Q: An open cylindrical tank 1.2 meters in diameter and 2.1 meters high is 2/3 full of water. After…

A: Given- Diameter of tank D=1.2 mHeight of tank H=2.1 mWater is 2/3 fullWater depth after rotation=0.3…

Q: Moving Question 37 A pressure gage 10.82 m. above the bottom of a tank containing a liquid reads…

Q: Problem 2 Determine: (1) What is the torque in tube (G=100 GPa) and rod (G=45 GPa)? (2) What is the…

A: Given data: Gtube = 100 GPa Grod = 45 GPa L = 1m D = 60 mm

Q: A water strikes to a vane with stationary velocity 25 m/s as shown in the Figure 3. It is given the…

Q: Problem 2 -40 In the figure shown, the deflection of mercury is initially 250 mm. If the pressure at…

A: We have to find the value of new mercury level when increased level of Mercury at A while at B…

Q: 8.35 PLUS Oil with a kinematic viscosity of 4 X 10-6 m²/s flows through a smooth pipe 12 cm in…

A: Velocity is generally the rate at which the location differs. The average velocity is the…

Q: A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.55 mm. The nozzle shoots…

Q: A vertical jet of water leaves a nozzle at a speed of 10 m/s and a diameter of 20 m. It suspends a…

Q: In the figure below, a block is sliding down over a liquid film. Calculate the average pressure (in…

A: Given data in question Weight of block Angle of inclination Thin liquid film Base area To find out…

Q: A block(unit weight = 19.5 kN/m^3) 0.56m square and 395mm deep floats on a stratified liquid…

Q: To what height will the jet of fluid rise for the conditions shown in the figure?

Q: Oil (SG = 0.90) flows downward through a vertical pipe contraction as shown in the figure If the…

Q: Figure 1 shows the manometer apparatus with different fluids. mercury and oil are 13.56, and 0.9…

A: Given data in question Specific gravity Depth Area ratio Volume x = Volume y To find out Delta Z…

Q: A U-tube containing mercury is used to measure the pressure of an oil of specific gravity 0.82 as in…

A: Given: The specific gravity of oil is 0.82. Consider the figure,

Q: A hollow cylinder 1.55m in diameter and 7m long weighs 3,055N. How many cubic meters of metal…

Q: The head of water over an orifice of diameter 100.mm is 10 m. The water coming out from orifice is…

Q: SITUATION: An open cylindrical vessel 1.3 m in diameter and 2.1 m high is 2/3 full of water. If…

Q: Calculate the pressure decrease (in psi) when you climb from an elevation of 660 ft to a mountain…

A: given h1 = 66o ft h2 = 1640 ft unit weight of air is constant at 0.07967 lb/ft^3. find the…

Q: 2. A single coloumn manometer is connected to a pipe containing a liquid of specific gravity 0.75.…

Q: A woman has a mass of 60 kg and her shoe heel has a diameter of 0.01 m. What is the pressure at…

Q: Open to atmosphere, pa hi= 38cm -Mercury (13,593 kg/m³) Water h,=76 cm B and C are at the same…

A: Atmospheric pressure- It is the pressure exerted by the atmosphere and it is measured by Barometer.…

Q: The pressure exerted at a point of the hull of the deep submersible vehicle is 3.00 × 106 Pa…

A: the hull of theThePressure exerted at a Pointdeep Submersible vehicle is 3x 106 Pa (Pascals).A…

Q: 13. A beaker of height 30 cm is partially filled with a liquid and is rotated by an angle 0 as…

A: Gauge pressure is pressure relative to atmospheric pressure; it is positive for pressures greater…

Q: 23. A hemispherical tank having a radius of 2.5 m is filled with water to a depth of 1.8 m. If a…

A: As per rule , I had done only civil engineering questions, ie. 21 and 23 solution . 21

Q: An open cylindrical vessel 1.2 m in diameter and 2.1 m high is 2/3 full of water. Compute the amount…

A: To determine the volume of water spilled. Given, Diameter of the tank, say D = 1.2 m Height of…

Q: A pressure gage 7.5m above the bottom of the tank containing a liquid reads65.45 kPa; another gage…

Q: A ball weighing 1 kg is “floating" on a circular jet, as shown in the figure (ignore the wire, which…

Q: Situation 3: A calibrated test of a 0.00785 m² circular sharp-edge orifice in a vertical side of a…

A: Given data : The value of weight of water W=22300 N The value of horizontal distance X=1.92 m The…

Q: If the system is in equilibrium, calculate the magnitude of F2. F = 100 KN Fz= ? 30° 30° 105°

A: • As per our guideline we are supposed to answer only one question for multiple questions posted.…

Q: A 425-Newton stone cube having 28-centimeters sides is lowered into a rectangular vessel. If the…

Q: Air is introduced through a nozzle into a tank of water to form a stream of bubbles. If the bubbles…

A: Given: Bubble diameter=2mm Surface tension of water=0.073 N/m P0=100 kPa

Q: flowing through a venturimeter shown. The difference in dusing open tubes. If h is 50cm, solve the…

Q: Determine the acceleration of the system shown. 30 30 12 kg 8 kg

Q: A pressure gage 10.52 m. above the bottom of a tank containing a liquid reads 58.5 kPa; another gage…

A: Using pressure variation equation the value of density can be easily determined. Knowing the…

Q: Problem 1.2 Two water tanks are connected to each other through a mercury manometer with inclined…

A: Asked: To determine the value of angle theta θ. Given: Pressure in tank A (PA) = 20 kPa Pressure…

Q: Situation #3: A weight concentrated at the end of a cord forms a conical pendulum for which the…

A: To find Velocity of weight?

Q: A hemisphere of radus 12 nches and base up is full of water that runs out through an orifice of area…

A: Given data, Radius of hemisphere = 12 inch Area of orifice = 1 in² Orifice coefficient = 1.0…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

12. A beaker of height 15 cm is partially filled
with a liquid and is rotated by an angle 0 as
shown.
If the pressure at point B becomes 5 bar,
what will be the value of 0?
A
15 cm
a) 30°
b) 50°
c) 60°
d) 70°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A vertical conduit is carrying oil (S = 0.95). A differential mercury manometer is tapped into the conduit atpoints A and B. Determine the difference in pressure between A and B when h = 3 in. What is thedifference in piezometric head between A and B?
A closed cylindrical tank 1.845m high and 0.945m in diameter contains water of height 1.35m. When the angular velocity is constant at 20rad/sec , If it is rotated at 15rad/sec and the air has a pressure of 200kPa what is the minimum pressure at the bottom of the tank in KPa? CHOICES a.) 220.48 b.) 22.48 c.) 202.48 d.) 248.22
A hemispherical tank having a radius of 2.5 m is filled with water to a depth of 1.8 m. If a solid sphere having a diameter of 1.8 m is placed on the bowl, determine how high will the water rise on the bowl. A. 116 mm B. 166 mm C. 176 mm D. 171 mm
A vertical conduit is carrying oil (S=0.95) as shown in figure 2. A differential mercury manometer is tapped into the conduit at points A and B. Determine the difference in pressure between A and B when h=3in. What is the difference in piezometric head between A and B?
How many kN of lead (SG=11) must be fastened outside the bottom of a 1-m diameter cylinder to make it float vertically with 1.5 m above the water? Weight of cylinder = 3562 N, Height of the cylinder = 4 m 17.270 kN 25.679 kN 23.405 kN 19.262 kN
A block (unit weight = 19.5 kn/m^3) 0.50m square and 382mm deep floats on a stratified liquid composed of 200mm layer of water above a layer of mercury (s.g. = 13.6) If a downward force of 1200 N is applied to the center of mass of this block, what is the new position of the bottom of the block relative to the mercury surface in mm?
an open circular vessel is 1m in diameter and 2m in height. it contains water filled to a depth of 1.5m. if the cylinder rotates about its vertical axis, what is the pressure intensity at the center of the bottom if w= 6 radians/second? (Unit of the correct answer : kPa) CHOICES a.) 12.465 b.) 21.456 c.) 16.425 d.) 15.542
Two barometers are put at the same location. The specific weight of liquid of the first barometer is γ1 = 10.77 kN/m3, and the specific weight of the second one is γ2 = 11.06 kN/m3. If the liquid height to the freesurface of the first barometer is h1 = 8.26 m, calculate the liquid height of the second barometer, h2_______m
. The head of water over an orifice of diameter 100 mm is 10 m. The water coming out from the orifice is collected in a circular tank of diameter 1,5 m. The rise of water level in this tank is 1.0m in 25 seconds. Also the coordinates of a point on the jet, measured from vena contracta are 4.30 m horizontal and 0.50 m vertical. Find the device coefficients.
An elevated water tank consists of an upper cylindrical part (4.88 m in diamwter and 6.10 m high) and a lower hemispherical part, at the lowest point of which is an orifice 310 mm in diameter (C=0.60). If, at time t=0, the tank is full of water, when will the water level drop down 6.71m, after opening the orifice? 35 seconds 415 seconds 235 seconds 260 seconds
A cylindrical tank contains a certain liquid (SG = 2.75) to a depth of 0.4 m. A pressure of 78 kPa is acting at the surface of the liquid. If it is accelerated upwards at 3.43 m/s2, what is the resulting pressure (kPa) at the bottom of the tank?
A water tank has sloping inclined at 45degrees with the horizontal. The total depth of water in the tank is 10m. A water jet is issues from an orifice located on the inclined side of the tank under a hydrostatic head of 8m and 2m vertically above the bottom of the tank. Coefficient of velocity is 1. Determine its time it takes for the particle of the jet to sit around that 1.5m below the bottom of the tank in seconds.a. 2.14sb. 2.05sc. 2.83s d.2.35s