12.125 A 500-lb crate B is suspended from a cable attached to a 40-lb trolley A which rides on an inclined I-beam as shown. Knowing that at the instant shown the trolley has an acceleration of 1.2 ft/s² up and to the right, determine (a) the acceleration of B relative to Ã, (b) the tension in cable CD.

12.125 A 500-lb crate B is suspended from a cable attached to a 40-lb trolley A which rides on an inclined I-beam as shown. Knowing that at the instant shown the trolley has an acceleration of 1.2 ft/s² up and to the right, determine (a) the acceleration of B relative to Ã, (b) the tension in cable CD.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 500-lb crate B is suspended from a cable attached to a 40-lb trolley A which rides on an inclined I-beam as shown. Knowing that at the instant shown the trolley has an acceleration of 1.2 ft/s2 up and to the right, determine (a) the acceleration of B relative to A, (b) the tension in cable CD.
Help!!!!! A 500-lb box B is suspended from a cable attached to a 40-lb truck A mounted on an I-beam inclined in the form that shows. If at the indicated time the truck accelerates 1.2 ft / s2 up and to the right, determine (a) the acceleration of B in relation to A and b) the tension in the CD cable.
A single wire ACB passes through a ring at C attached to a sphere that revolves at a constant speed v in the horizontal circle shown. Knowing that the tension is the same in both portions of the wire, determine the speed v.
An 8-kg cylinder C rests on a 4-kg platform A supported by a cord that passes over the pulleys D and E and is attached to a 4-kg block B. Knowing that the system is released from rest, determine (a) the velocity of block B after 0.8 s, (b) the force exerted by the cylinder on the platform.
A 0.5-kg block B slides without friction inside a slot cut in arm OA that rotates in a vertical plane. The rod has a constant angular acceleration 0= 10 rad/s2. Knowing that when 0= 45° and r= 0.8 m the velocity of the block is zero, determine at this instant, (a) the force exerted on the block by the arm, (b) the relative acceleration of the block with respect to the arm.
Two wires AC and BC are tied at C to a sphere that revolves at a constant speed v in the horizontal circle shown. Determine the range of the allowable values of v if both wires are to remain taut and if the tension in either of the wires is not to exceed 60 N.
A 40-lb sliding panel is supported by rollers at B and C. A 25-lb counterweight A is attached to a cable as shown and, in cases a and c , is initially in contact with a vertical edge of the panel. Neglecting friction, determine in each case shown the acceleration of the panel and the tension in the cord immediately after the system is released from rest.
A spring AB of constant k is attached to a support at A and to a collar of mass m. The unstretched length of the spring is 1 . Knowing that the collar is released from rest at x=x0 and neglecting friction between the collar and the horizontal rod, determine the magnitude of the velocity of the collar as it passes through point C.
A 12-lb block B rests as shown on the upper surface of a 30-lb wedge A. Neglecting friction, determine immediately after the system is released from rest (a) the acceleration of A, (b) the acceleration of B relative to A.
A 25-kg block A rests on an inclined surface, and a 15-kg counterweight B is attached to a cable as shown. Neglecting friction, determine the acceleration of A and the tension in the cable immediately after the system is released from rest.
A 500-g collar can slide without friction on the curved rod BC in a horizontal plane. Knowing that the undeformed length of the spring is 80 mm and that k= 400 kN/m, determine (a) the velocity that the collar should be given at A to reach B with zero velocity, (b) the velocity of the collar when it eventually reaches C.
A 10-kg block is attached to spring A and connected to spring B by a cord and pulley. The block is held in the position shown with both springs unstretched when the support is removed and the block is released with no initial velocity. Knowing that the constant of each spring is 2 kN/m, determine (a) the velocity of the block after it has moved down 50 mm, (b) the maximum velocity achieved by the block.