120 mm A V B D 300 mm 80 N 80 N B 30 mm A 30 mm D D 12 mm 12 mm

Q: 2. Determine the components of all forces acting on each member of the loaded frame. 5 kN 1.5 m 1.5…

A:

Q: (Q1] Replace the system shown below by a single force at B and a couple. 700 N 30 450 N 300 N 60 BY…

A:

Q: Replace the loading on the frame by a single resultant force. Suppose that Fi = 250 lb , F2 = 90 lb…

A: Given data as per question F1 =250 lb F2 = 90 lb M =500 lb. ft considering horizontal forces  as…

Q: 4 kN/m А В 6 т

A: Consider horizontally forward & vertically upward force as (+)ve and vertically downward force…

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is…

A: There will be two reactions at thrust bearing and tension in the cable. Since Force F acts in single…

Q: A truss used for supporting signs over an expressway is shown. The truss is supported by a pin at…

A:

Q: Forces of 50 lb are applied to the handles of the bolt Determine the force exerted on the cutter of…

A:

Q: Q4: The forces F1 and F2 act on a bracket as shown in the Figure below. Determine the magnitude of…

A: Step-1                  Given Data                                         F1=100 N…

Q: the homogeneous cylinder of weight W=100 N rests in a frictionless right angled corner. determine…

A:

Q: PROBLEM NO. 2: For the system of forces shown, de termine the vertical component of the resultant of…

A:

Q: The L-shaped body is supported by a roller at B and a frictionless pin at A. The body supports a…

A:

Q: 12 m A 24 m M 20 m 24 m Control arm AB is subjected to a counter clockwise moment, M and held in…

A: Introduction: The turning impact of force is referred to as the moment of force. It is the product…

Q: 120 N P PROBLEM 2.17 25° For the stake of Prob. 2.5, knowing that the tension in one rope is 120 N,…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: Two horizontal beams are used to balance the masses A, B, and C, as shown in the figure. Each beam…

A: Given data Mass(Mc)= 30kg Need to determine the tension force in each cable

Q: The bar of negligible weight is supported by two springs, each having a stiffness k = 98 N/m. If the…

A:

Q: die is being used to cut threads on a rod. If 30-lb forces are applied as shown, determine the…

A:

Q: Determine the force in member BC. a 4.50 kN(C) c 8.00 kN(C) b 6.00 kN(C) d 14.00 kN(C) Determine the…

A: The free-body diagram of the given truss can be drawn as below, Here RC is the horizontal reaction…

Q: To loosen a frozen valve, a force F with a magnitude of 70 lb is applied to the handle of the valve.…

A:

Q: The force P on the handle of the positioning lever produces a vertical compression of 56 lb in the…

A: Given that ,  a=3.4 in b=8.6 in

Q: The force P on the handle of the positioning lever produces a vertical compression of 56lb in the…

A: the magnitude of the corresponding force exerted by the pin at O.

Q: A force of 90 N is applied on a lever AB as shown in the figure. Knowing that the lever is 225 mm…

A: given force F=90Nlength of lever AB L=225mm=0.225mmoment about point B is MB=13.5Nmα= angle makes by…

Q: 3.78 The 200-kg slider at A is held in place on the smooth vertical bar by the cable AB. (a)…

A:

Q: . Determine the support reactions and internal forces N, V, and M that occur midway between supports…

A:

Q: 2/A rocker arm with rollers at A and B is shown in the position when the valve is open and the valve…

A:

Q: ie is being used to cut threads on a rod. If 18-Ib forces are applied as shown, determine the…

A: Given:P=18 lbr=7.5 inx=0.5 in

Q: Determine the magnitude of the gripping forces produced when two 300-N forces are applied as shown.

A: Free body diagram of the problem is shown in the figure. Member AC is connected to both members AB…

Q: A truss supports the loading shown. Determine the equivalent force acting on the truss and the point…

A: Write the all forces in the vector form.…

Q: In order to unscrew the tapped faucet A, a plumber uses two pipe wrenches as shown. By exerting a…

A: Given Magnitude of force = 40 lb Wrench distance = 10 in To find The angle θ that the wrench at A…

Q: A frame ABC is supported by cable DBE that passes throught the ring at B. Assuming tension force in…

A:

Q: Determine the magnitude of the force supported by the pin at C of the loaded frame.

A:

Q: (Q1] Replace the system shown below by a single force at B and a couple. 700 N |30 450 N 300 N 60 B…

A: Solution:

Q: A beam supports three loads of given magnitude and a fourth load whose magnitude is a function of…

A: The beam is given as follows, Ballance the force in the y-direction to get the resultant equivalent…

Q: The crane pulls a fixed object in D using the CD cable. The crane is supported on bearings at E and…

A:

Q: 2. A loading car, as given in figure, is at rest on a track forming an angle of 25° with the…

A: Given data: The angle formed by the track with the vertical is θ=25°. The weight of the car and…

Q: Four signs are mounted on a frame spanning a highway, and the magnitudes of the horizontal wind…

A: required the magnitude and the point of application of the resultant of the four wind forces when a=…

Q: As shown in the image below, the 89-lb crate is supported by three ropes as shown. The coefficients…

A:

Q: In order to unscrew the tapped faucet A , a plumber uses two pipe wrenches as shown. By exerting a…

A: The free-body diagram of pipe ABC is shown as, The coordinates of the points are given as,

Q: the 480 kg bent bar ABC of uniform cross section is supported by a pin at A and a vertical cable at…

A:

Q: PROBLEM 2: Determine Pand 6 so that the three forces shown are equivalent to the single force R =…

A: Given data,  R is resultant where R= 85i + 20j kN  Need to find P and θ

Q: 3/42 A rocker arm with rollers at A and B is shown in the position when the valve is open and the…

A:

Q: a d2 d2 d3 F lb B F lb a d1 = 5.19 in %3D d2 = 0.82 in d3 = 0.5 in

A:

Q: A frame and loading are shown. B 90 mm D 120 mm ' 120 mm' 120 mm Determine the force acting on…

A:

Q: A 170-kg horizontal beam is supported at the ends A and B. A 300-kg piano rests a quarter of the way…

A:

Q: The guy wire BD exerts on the telephone pole AC a force P directed along BD. Knowing that P must…

A: Calculate the angle made by force P with vertical as follows: tanθ=72.4θ=tan-172.4=71.1° Draw the…

Q: A dirigible is tethered by a cable attached to its cabin at B. If the tension in the cable is 1040…

A: Take moment about A ∑MA=0Fccos30°(6.7+4)+1040cos30°(6.7)=0Fc=-651.21N

Q: Two bolts at A and B are used to move the trunk of a fallen tree. Replace the forces exerted by the…

A: Given Data Force acting in AC is: FAC=1650 N Force acting in BD is: FBD=1500 N Coordinate of A is…

Q: In using the bolt cutter shown, a worker applies two 300-N forces to the handles. Determine the…

A: Applying∑Fx=0SoBx=0taking moment about A∑MA=096By-24Q=096By=24QQ=4By...........1

Q: 4. The block shown is acted on by its weight W = 400 lb, a horizontal force F = 600 lb, and the…

A: The vector sum of two or more vectors is the outcome. It's the outcome of combining two or more…

Q: Adie is being used to cut threads on a rod. If 27-lb forces are applied as shown, determine the…

A: Given data,  P= 27 lb is applied at both end.  Handle length is 5 inches. Diameter of die is d=…

Q: Suppose P = 2500 lb. From the frame below, determine the magnitude and direction of (1) Ax and Ay…

A: Given data P=2500 lb

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.