The force P on the handle of the positioning lever produces a vertical compression of 56lb in the coiled spring in the position shown. Determine the magnitude of the corresponding force exerted by the pin at O on the lever. Assume a = 3.4in. b = 8.6in

Q: * 1. The light bar is used to support the m kg block in its vertical guides. If the coefficient of…

A: (a) Draw the free-body diagram of the block. Apply force equilibrium in vertical direction.…

Q: 1) The force/weight criteria to choose the working energy is higher in than (A) hydraulic,…

A: Concept: 1) In general in choosing force criteria, working energy is higher in hydraulic than…

Q: Calculate the discharge throug

A: To find Discharge

Q: A {m} kg disk of constant thickness and radius 9.4 m, initially at rest, is placed in contact with a…

A:

Q: When a horizontal roll vortex is pushed vertical, what is created?

A: The wind shear causes the air to have a horizontal rotation. The strong updrafts from the rising…

Q: The motion of the particle along a straight line is governed by the relation a = t3 – 2t2 + 7 where…

A: Let represent point A in t= 1.42478 s and point B in t= 2 s. Given: a= t3 - 2t2 + 7 When tA= 1.42478…

Q: Determine the reactions at A and B for the beams loaded as shown

A: According to the details provided in the question, we need to calculate reactions

Q: Viscosity coefficient (n) of-3 fluid defines the . between shear stress and rate .of change shear…

A:

Q: 1) A cup-drawing operation is performed in which: The cup's inside diameter = 75 mm and its height =…

A: Given Datad=75mmh=50mmt=3mmRd=4mmσt=400MPa

Q: Draw the shear and bending-moment diagrams for the beam and loading shown

A:

Q: 4. At the instant shown, the crank AB is rotating with a constant counterclockwise angular velocity…

A:

Q: Use the manning's equation above to find the streamflow rate (Q) under the following conditions: a.…

A: Given                       Width, B = 1000 m                       Depth, Y = 2 m Conversion…

Q: The proper representation of the force of a flexible cable, belt, chain, or rope if the weight of…

A:

Q: 4.9 A 1200-lb load is supported by a cable that runs over a small pulley at E and is anchored to a…

A: find the reactions at the supports and draw free body diagrams.

Q: The concrete block shown has wall thicknesses of 40 mm, voids that are 95 mm x 110 mm, and is 190 mm…

A:

Q: kindly help me with this one. Write your answer with four decimal places and enclose them in a box.…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A square plate of 0.255 kg mass and 0.5 m side slides down a plane, inclined at an angle of 30° to…

A: Mass of the square plate, m= 0.255 kg Side length of the square plate, b= 0.5 m Angle, θ= 30∘…

Q: 1.40 Convert the following quantities to the designated SI units: (a) 627 in? to mm² and m2 (b) 14…

A: As per our guidelines, we are supposed to answer only first three subparts in case of multiple…

Q: ersed rectangular plate as shown in the figure. Free water surface Im b-3 m

A: Solution is attached below:

Q: In a Diesel Cycle, the compression ratio is 15. Compression begins at 0.1 MPa, 40 deg. C. The heat…

A:

Q: The following data were recorded during the tensile test of a 9-mm-diameter mild steel rod. The gage…

A:

Q: calculate the leakage mass flow rate per unit area from the first ring pack plenum to the cylinder…

A: Xdff

Q: For The beam shown in The Figure belwe find deflection at paint B 2. EI-12000 K Ne m² P=50 KN m=25…

A:

Q: It is observed that the skier leaves the ramp A at an angle 0= 25 with the horizontal. If he strikes…

A: (d) Write the expression of radius of curvature at point A. mgcosθA=mvA2RR=vA2gcosθA

Q: yth at the $ 6m/S and 18m/ points (-2,0) Determine the Hive ly Ve

A:

Q: Consider a steam power plant that operates on a regenerative Rankine cycle and has a net power…

A: Given that: For the regenerative Rankine cycle, Turbine inlet conditions are P5 = 10 MPa, T5 = 500…

Q: A supercooled water droplet turning into ice is called ____________.   a. c. deposition   b. e.…

A: Concept: 1) Water droplets generally in liquid state.  2) While supercooling, the temperature of…

Q: Determine the stream function if the velocity components in a steady 2D flow field are as follows:…

A: u= 3y v= 5x

Q: Q1/"Current trend in Energy Supply and use are patently unsustainable-economically, environmentally…

A: C)The main idea of the given article is the use of the low carbon technologies have a crucial role…

Q: What is the value of the torsion constant for the beam cross section shown below? 60 mm 20 mm 20 mm…

A:

Q: Q5: Cooling water at a steady rate of 0.5 kg/s flows through an inner tube having inner diameter of…

A: Given, Mass flow rate of cooling water = m' = 0.5 kg/s Inner tube diameter = d = 25 mm = 0.025 m…

Q: According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength…

A:

Q: The state of stress at a point is shown on the element. Determine (a) the principal stress and (b)…

A:

Q: Shafts AB and CD are used to transmit power from the motor at A to a machine tool E (idealized as a…

A: Given data Material of AB : SteelGAB = 78 GPadiameter of AB = d1 = 52.5 mmthickness of AB = t = 15…

Q: Two pipes are connected in series having a length and friction factor, “f” equal to each other. If…

A: Solution.jpg

Q: The lengths of two pipes with the same friction factor, "f," are parallel. What must the flow ratio…

A:

Q: 5- An air-standard Diesel cycle has a compression ratio of 19. Air is at 130°F and 14.7 psia at the…

A:

Q: where are you finding v=0.0159939 m3/kg ? , when I look for the specific volume for saturate steam…

A:

Q: Air enters a rectangular duct measuring 30 cm by 40 cm with a velocity of 8.5 m/s and a temperature…

A:

Q: 2. A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 58L/s of water. The…

A: Suction pipe diameter, d1=260 mm=0.26 mDischarge pipe diameter, d2=150 mm=0.15 mWater flow rate,…

Q: Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady,…

A: (1) Draw the diagram of the venturi meter.

Q: A thick wall cylinder has 50 mm thick and internal diameter of 300 mm. If stress is limited to 30…

A:

Q: 25. Consider the torsionally loaded thin-walled member with a shear modulus (G) = 26e9 N/m?. 6ON-m…

A: Given data Shear modulus = G = 26 x 109 N/m2a = 0.8 mb = 0.4 mthickness = s =0.04 mlength = 3.2 mT =…

Q: what is meant by each of the following? 1. Refrigerant 2. GWP factor 3. TEWI

A: To find :- Defination of terms

Q: Use the manning's equation above to find the streamflow rate (Q) under the following conditions: a.…

A:

Q: he velocity of steam at ne nozzles are inclined et blade angle is 30° SI blade efficiency, and

A:

Q: 2-For the shown manipulators find the equation of motion. Y A Fx Mar Fz Fy: X I ng X2

A: Given : To find : Equation of motion

Q: From the the double slider-crank mechanism shown in Fig.A (a) Determine the number of Instantaneous…

A:

Q: Determine the hoop stress on the outer surface of the cylinder.

A:

Q: The pressure at a point in the fluid is 4.9 Nem2 Find height when the fluid under consideration is…

A: given data :- pressure at a point is 4.9 N/cm^2 specific gravity of oil is 0.85 . find the height.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.