1 1. (13.13) To make a secure fit, rivets that are larger than the rivet hole are often used andthe rivet is cooled (usually in dry ice) before it is placed in the hole. A steel rivet 1.872cm in diameter is to be placed in a hole 1.870 cm in diameter in a metal at 22°C. To whattemperature must the rivet be cooled if it is to fit in the hole?2. (13.24) In an internal combustion engine, air at atmospheric pressure and atemperature of about 20°C is compressed in the cylinder by a piston to of its originalvolume (compression ratio = 9.0). Estimate the temperature of the compressed air,assuming the pressure reaches 40 atm.3. (13.29) What is the pressure inside a 38.0-L container holding 105.0 kg of argon gas at21.6°C?4. (13.49) If the pressure in a gas is tripled while its volume is held constant, by what factordoes Urms change?

"Since you have asked multiple questions, as per instructions to us, we will solve the first…

(13.13) To make a secure fit, rivets that are larger than the rivet the rivet is cooled (usually in dry ice) before it is placed in the hole. A steel rivet 1.872 cm in diameter is to be placed in a hole 1.870 cm in diameter in a metal at 22°C. To what temperature must the rivet be cooled if it is to fit in the hole?

(13.13) To make a secure fit, rivets that are larger than the rivet the rivet is cooled (usually in dry ice) before it is placed in the hole. A steel rivet 1.872 cm in diameter is to be placed in a hole 1.870 cm in diameter in a metal at 22°C. To what temperature must the rivet be cooled if it is to fit in the hole?

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter16: Temperature And The Kinetic Theory Of Gases

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

At 25.0 m below the surface of the sea, where the temperature is 5.00C, a diver exhales an air bubble having a volume of 1.00 cm3. If the surface temperature of the sea is 20.0C, what is the volume of the bubble just before it breaks the surface?
Why does rubbing alcohol evaporate much more rapidly than water at STP (standard temperature and pressure)?
How much stress is cleated in a steel beam if its temperature changes from 15 to 40 but it cannot expand? For steel, the Young's modulus Y=210109N/m2 from Stress, Strain, and Elastic Modulus (http://cnx.org/content/m58342/latest/#fs-id1163713086230). (Ignore the change in area resulting from the expansion.)
A brass rod (Y=90109N/m2), with a diameter of 0.800 cm and a length of 1.20 m when the temperature is 25 , is fixed at both ends. At what temperature is the force in it at 36,000 N?
The mass of a hot-air balloon and its cargo (not including the air inside) is 200 kg. The air outside is at 10.0C and 101 kPa. The volume of the balloon is 400 m3. To what temperature must the air in the balloon be warmed before the balloon will lift off? (Air density at 10.0C is 1.244 kg/m3.)
When resting, a person has a metabolic rate of about 3.88 x 105 joules per hour. The person is submerged neck-deep into a tub containing 4.62 x 103 kg of water at 26.9 °C. If the heat from the person goes only into the water, find the water temperature in degrees Celsius after half an hour.
A brass plug is to be placed in a ring made of iron. At 15 degree C of the plug is 8.755 cm and that of the inside of the ring is 8.741 cm. They must be both be brought to what common temperature in order to fit?
and the length of the copper section is 0.800 mm. Each segment has cross-sectional area 0.00700 m2m2. The free end of the brass segment is in boiling water and the free end of the copper segment is in an ice-water mixture, in both cases under normal atmospheric pressure. The sides of the rods are insulated so there is no heat loss to the surroundings. What mass of ice is melted in 6.00 min by the heat conducted by the composite rod?
To make a secure fit, rivets that are larger than the rivet hole are often used and the rivet is cooled (usually in dry ice) before it is placed in the hole. A steel rivet 1.877 cm in diameter is to be placed in a hole 1.875 cm in diameter at 15 ∘C.To what temperature must the rivet be cooled if it is to fit in the hole? A small immersion heater is rated at 375 W . The specific heat of water is 4186 J/kg⋅C∘.Estimate how long it will take to heat a cup of soup (assume this is 250 mL of water) from 19 ∘C to 72 ∘C. Ignore the heat loss to the surrounding environment. A 52 g ice cube at its melting point is dropped into an insulated container of liquid nitrogen. Assume for simplicity that the specific heat of ice is a constant and is equal to 2100 J/kg⋅C∘.How much nitrogen evaporates if it is at its boiling point of 77 K and has a latent heat of vaporization of 200 kJ/kg?
A pair of eyeglass frames are made of epoxy plastic (coefficient of linear expansion 1.30x10−4 °C−1). At room temperature (20.0 °C), the frames have circular lens holes 1.80 cm in radius. To what temperature must the frames be heated if lenses 1.81 cm in radius are to be inserted into them?
Two rods, one made of brass and the other made of copper, are joined end to end. The length of the brass section is 0.200 m and the length of the copper section is 0.800 m. Each segment has cross-sectional area 0.00700 m^2. The free end of the brass segment is in boiling water and the free end of the copper segment is in an ice-water mixture, in both cases under normal atmospheric pressure. The sides of the rods are insulated so there is no heat loss to the surroundings. What mass of ice is melted in 6.00 min by the heat conducted by the composite rod?
A steel ring with a hole having area of 3.990 cm2 is to be placed on an aluminum rod with cross-sectional area of 4.00 cm2. Both rod and ring are initially at a temperature of 35 degrees celcius. At what common temperature can the streel ring be slipped onto one end of the aluminum ring?