16. Consider the flow of a fluid between two large parallel flat plates located at a distance of 2A apart. ex2A 24 Find the governing momentum equation for the flow between the plates for the condition that the velocity profile is fully developed. [Hint: In this case, the net momentum flux is zero].

16. Consider the flow of a fluid between two large parallel flat plates located at a distance of 2A apart. ex2A 24 Find the governing momentum equation for the flow between the plates for the condition that the velocity profile is fully developed. [Hint: In this case, the net momentum flux is zero].

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.3P: Evaluate the Nusselt number for flow over a sphere for the following conditions: D=0.15m,k=0.2W/mK,...

See similar textbooks

Similar questions

The external and internal diameters of the inward flow reaction turbine 60 cm and 30 cm, the width of the inlet are 15 cm. The flow velocity through the runner is constant throughout and is equal to 1.5 m/s. Calculate discharge and the width at the outlet if 8% of the circumferential area is occupied by the blade thickness at both inlet and exit.
6.36 This two-dimensional water (at 50°F) jet is deflected by the two-dimensional vane, which is moving to the right with a speed of 60 ft/s. The initial jet is 0.30 ft thick (vertical dimension), and its speed is 100 ft/s. What power per foot of the jet (normal to the page) is transmitted to the vane? See §6.5 for useful knowledge about moving CVs.
A cart with frictionless wheels and a large tank shoots water at a deflector plate, turning it by angle ? as sketched. The cart tries to move to the left, but a cable prevents it from doing so. At the exit of the deflector, the water jet area Ajet, its average velocity Vjet, and its momentum flux correction factor ?jet are known. Generate an expression for the tension T in the cable in terms of the given variables.
Please indicate the given, assumption and illustration. A source with strength 0.25 m2/s and a vortex with strength 1 m2/s (counter-clockwise) are located at the origin. After working out the equations for the stream function and velocity potential components, determine the following velocity components at a point P(1, 0.5): A) The Radial Velocity component in meters/second. B) The Tangential Velocity Component in meters/second.
04/13/2021 For this exercise Study and Derive the Bernoulli equation starting with the application of Newton’s second law to a fluid particle.
11- When a jet strikes an inclined fixed plate, as shown, it breaks into two jets at 1 and 2 of equal velocity V but unequal areas. The reason is that for frictionless flow the fluid can exert no tangential force Ft on the plate. The condition Ft=0 enables us to solve for Ft=0. Perform this analysis, and find the ratio Q1/Q2.
Water flows through a rectangular duct of height h = 575.5 mm and width b = 100 mm.(coming off screen) and enters a 90° elbow. At the entrance of the elbow, flow can be considereduniform with speed U = 58 m/s. At the output, a linear velocity profile must be consideredas shown in the figure, where Vmax = 2Vmin. Calculate the value of Vmin in m/s.
Describe Applications of momentum equations.
A semi-infinite body is constructed from a uniform flow with velocity V∞ and a source with strength Λ = 879 m2/s at the origin. The stagnation point on the body is located at location (r,θ) = ( 13.8 m, π ). Determine the uniform flow velocity V∞, the coordinates (x, y), and the velocity components (Vx, Vy) at a point on the surface of the body with θ = 2 rad. V∞ = ___ m/s x = ___ my = ___m Vx = ____m/sVy = ____m/s
A horizontal water jet of constant velocity V impinges normally on a vertical flat plate and splashes off the sides in the vertical plane. The plate is moving toward the oncoming water jet with velocity 1/2V. If a force F is required to maintain the plate stationary, how much force is required to move the plate toward the water jet?
The parabolic velocity distribution in a channel flow is given by u(y) = 0.2(1 − y^2) m/s with y measured incentimeters. What is the acceleration of a fluid particle on the centerline where y = 0? At a location where y = 0.5cm?
A nozzle inclined at an angle of 68° with the horizontal issues an 82-mm-diameter water jet at a rate of 14 m/s. What is the area (in sq. m.) of the jet at the highest point of the projectile? Neglect air resistance.