Given data:Maximum shear stress350 MPaMaximum principal stress=80 MPaFind minimum principal stress

Answered: Image /qna-images/answer/02539ef5-4830-43e4-bc87-6aa757b39814.jpg

Answered: Given data: Maximum shear stress-50 MPa…

Engineering

Mechanical Engineering

Given data: Maximum shear stress-50 MPa Maximum principal stress=80 MPa Find minimum principal stress

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.4P: -4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa...

See similar textbooks

Related questions

Q: Create the front view of the sketch of the spur wheel (hand written)

Q: Compound axial member ABC has a uniform diameter of d = 1.0 in. Segment (1) is an aluminum [E1 =…

Q: 2.4 An 18-m-long steel wire of 5-mm diameter is to be used in the manufacture of a prestressed…

A: Given: E = 200 GPa elongation = 45 mm length = 18 m diameter = 5 mm Please note that in order to…

Q: The vertical reaction in the hinged support shown in the figure is Blank 1 N. 200 N 200 N D E D 2 m…

Q: The oven shown in the figure has a heating element with appreciable capacitance C. The other…

A: consider above given diagram:

Q: B. D. AB 45 cm BC 65 cm CD 77 cm RA - 60.25 N Ro 26.43 N P2 -47 N 10 N 5- A student conducted an…

Q: An observer notes that an approach to a pretimed signal has a maximum of eight vehicles in a queue…

Q: Find the determinant of the matrix by reducing the matrix to a triangular form. 1 3 14 9 1 15 D = -2…

A: given; D=1314391152-211-3423

Q: For the design of the band brake shown, find the couple M required to turn the pipe in the V-block…

A: Find the moment M.

Q: Saved Determine the capacity, in liters, of the punch bowl shown if R= 370o mm. (Round the final…

Q: The 20-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and…

A: Given Mass of disk, md = 20 lb Mass of plate, m = 5 lb Time, t = 1 sec…

Q: The 20-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and…

A: Given Mass of disk, md = 20 lb Mass of plate, m = 5 lb Time, t = 1 sec…

Q: For an engine working on the ideal Diesel cycle, the pressure and temperature at the inlet is 120…

A: Given Data: Inlet pressure, P1=120 kPa Inlet temperature, T1=30 C

Q: A spring balance is calibrated in an environment at a temperature of 20°C and has the following…

Q: Example 21.4. A, B, C and D are four masses carried by a rotating shaft at radii 100, 125, 200 and…

A: given; gap between balanced mass(d)=600mm radius of A (rA)=100mmradius of B (rB)=125mmradius of C…

Q: The 20-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and…

A: Given Mass of disk, md = 20 lb Mass of plate, m = 5 lb Time, t = 1 sec…

Q: In an ideal Otto cycle, the temperature at the start of the expansion process is 2500°F, and the…

A: Given Data: The temperature at the start of the expansion, 2500 F

Q: EXAMPLE 10.4 Discretize the equation boundary as shown in Fig. 10.6. aT T ax ay 0 at node (i,j) of a…

Q: A block is sliding from rest on a plane inclined downward 30° from the horizontal. The vertical…

Q: A rail line is laid so that there is no stress in rails at 15°C. The rails are 50 m long. α = 11.7 ×…

A: Temperature, T1= 15∘C Rail length, L= 50 m α= 11.7×10-6/∘C E= 2.3×105 N/mm2 Expansion allowance, ∆=…

Q: 10 mm 10 mm 30 mm 10 kN 30 mm 10 KN 25 mm The bottom force of 10 kN is 25 mm below the centroid Find…

A: Given: b = 15 mm To find: stress at point A = ?

Q: 2. A soccer ball with a outer diameter of 200mm and a thickness of 5mm is given. Compute the normal…

Q: HomeWork: Draw the shape below using the Front View for drawing in 2D and then the Southwest…

Q: The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel…

Q: section shown in figure Question 2, determine the shear stress a. In the Web at point A b. and in…

Q: 6/71 The weight of the drum D and its cable is 10o lb, and the coefficient of friction u for the…

Q: A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of…

Q: Q2: Explain the procedure of venture meter experiment.

Q: A Diesel air-standard cycle has a compression ratio of 17.6:1. The pressure and temperature at the…

A: Given dataDiesel air standard cycle has the following propertiesCompression ratio = CR= 17.6 =…

Q: Consider an air-standard Otto cycle that has a compression ratio of 7.8 and a heat addition of 1250…

Q: Example: 2.7 A hollow circular nylon pipe (see Fig 1-23) supports a load P = 7800 N, which is…

Q: The roof of a house consists of a 0.70-ft-thick concrete slab (k = 3 W/m · °C) that is 18 m wide and…

A: Given that, Thickness of concrete slab, t=0.70 ft,Thermal conductivity of the concrete, k=3…

Q: P7.6 A strain gage with a resistance of 120Q and a gage factor of 2 has a resistance change of…

A: A resistance gauge is used to measure the strain in a rectangular bar. Since we know formulate for…

Q: 4 kN/m 3 kN/m 6m 6m B

A: To determine the reactions at A.

Q: The absolute pressure in a gas tank is 300 kPa. Determine the gauge pressure. Calculate the…

Q: The capacity of the bowl is liters.

A: Given: R=370 mm To find : Capacity of bowl

Q: A six-lane freeway (three lanes in each direction) in rolling terrain has 10-ft lanes and…

A: To given thatfLW=6.0mphfLC=0.8mphTRD=1.5Now using relation for free flow…

Q: Problem 3: At the instant shown, the angular speed of rod AB is 2 rad/s counterclockwise. Using the…

Q: The static temperature of a moving fluid is O greater than stagnation pressure equals to stagnation…

Q: The 20-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and…

A: Given Mass of disk, md = 20 lb Mass of plate, m = 5 lb Time, t = 1 sec…

Q: Imagine an alternate universe where the value of the Plarnck constant is 6.62607 x 10 J.s. In that…

Q: A thin wall spherical tank of diameter 1.5 m and wall thickness 65 mm has internal pressure of 20…

Q: Q2): Dual problem below: Min Z = 120y, + 6y2 + 105y3 Subject to : Зу, + 5у2 + 8уз 23 10y, + 2y2 +…

Q: 3. The following data are given for a U-tube steam generator. Tube mass flow rate m =70E6 lbm/h,…

A: Head represents by the body force is known as hydrostatic head because of gravity when forced…

Q: If the heat rejected to the surroundings is 40% larger than the heat absorbed at the food…

Q: 2. A soccer ball with a outer diameter of 200mm and a thickness of 5mm is given. Compute the normal…

Q: Determine the magnitude of the shear force at section b-b that lies 0.1 m from A, located 0.1 m…

A: Find the shear force at section b-b.

Q: 1. Find the effective stiffness (keg) of the spring system shown below. -WWE

Q: Solve 5 problems (following the conditions stated below) involving the use of shear and moment…

Q: An Otto cycle has clearance volume of twelve percent. It produces three hundred kilowatts of power.…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Given data:
Maximum shear stress350 MPa
Maximum principal stress=80 MPa
Find minimum principal stress

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.