16. The rotational speed of lead screw depends on 17. Lead screw is connected to shaft though 18. is the set of the detailed step by step commands that direct the actions of the processing quipment. 19. For each pulse the motor rotates a fraction of revelation called 20. -----A device to measure the angular displacement.

16. The rotational speed of lead screw depends on 17. Lead screw is connected to shaft though 18. is the set of the detailed step by step commands that direct the actions of the processing quipment. 19. For each pulse the motor rotates a fraction of revelation called 20. -----A device to measure the angular displacement.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.1: Cnc Basics

Problem 7RQ: What is the name for the type of motor used to drive CNC axes that is also capable of recording axis...

See similar textbooks

Similar questions

Define angular impulse.
An offset slider crank mechanism has a crank length of 4 inches rotating at 25rpm counter-clockwise with an offset of 8 inches. The angle between the connecting rod and the slider path is 25o when the slider is at the head-dead-center.Determine d. time for the return and forward strokee. average velocity of the slider during return and forward stroke
The motion transmitted between the teeth of gears in mesh is *
Q6. Gear and Motor selection: For a 50 Hz supply frequency, the motor speed is 50 revolutions per second. What gearbox is required to step this down to 2 rad s−1 at the pulley wheel? What is the maximum torque to be developed by the motor? Round off your answers to one decimal place. -The gear ratio required is ? - The maximum torque to be developed by the motor is Nm ?
The max speed for the servo shown is 130RPM when connected to 6V. Assume that the gearbox on your servo is able to output a torque of 1.5 kg-cm while turning at this speed. Using the number of teeth on each gearprovided in the table, determine the torque and rotational speed of the output shaft on the DC motor. HINT: Work backwards from the output shaft and use the equations developed in class that relate the number of teeth to the torque. When working back from the output shaft to gear 7/6, realize that the “torque” transmitted by gear 7 is the SAME as the torque transmitted by gear 6 since they are joined. Then, relate the torque of gear 6 to gear 5 based on their numbers of teeth. Since gears 5 and 4 are actually one piece, the torque in 4 and 5 will be the same (as was the case for gears 6 and 7). Repeat for the other gears, working your way all the way back to the DC motor.
Identify which variables are the outputs or how they relate to the outputs. Plug in all possible numbers. Assuming link 2 rotates at a constant rate of 80 rpm CW, determine the velocity of link 6 when link 2 makes a 10-degree angle with the ground (measured as a right hand horizontal)
Position analysis of Scotch Yoke Mechanism What is the effect of change in crank length and angular velocity on the displacement v/s time curve of reciprocating part? Velocity analysis of Scotch Yoke Mechanism 2. What is the effect of change in crank length and angular velocity on the velocity v/s time curve on the reciprocating part ? Acceleration analysis of Scotch Yoke Mechanism 3. What is the effect of change in crank length and angular velocity on the acceleration v/s time curve of reciprocating part ?
a. Find out the equation describing the relationship between the rpm ofthe wheels, ?wheel, and the forward velocity, v, with thegiven parameters. b. Find out the relationship between the translational velocity of thewheels, vwheel, and the angular velocity, ?, assuming thewheels are rotating in opposite directions and with the same speed.
What is angular impulse?
In 40 seconds, the crankshaft of a truck engine operating at _______rpm turn thru 8000 radians.
If one node is observed at a frequency of 1000 RPM, during a whiring of a simply supported long slender rotating shaft. The first critical speed of the shaft in RPM is ______?
The 16 in. diameter pulley of a gasoline engine is connected by a pulley (which is assumed not to slip) to the pulley of apump. The belt speed is 4,000 fpm. Determine (1) the angular speed of the engine pulley in revolutions per minute and inradians per second; and (2) the diameter in inches of the pump pulley if the pump speed is one-half the speed of theengine pulley.