17-102. The 25-lb slender rod has a length of 6 ft. Using a collar of negligible mass, its end A is confined to move along the smooth circular bar of radius 3√2 ft. End B rests on the floor, for which the coefficient of kinetic friction is μ = 0.4. If the bar is released from rest when = 30°, determine the angular acceleration of the bar at this instant.

17-102. The 25-lb slender rod has a length of 6 ft. Using a collar of negligible mass, its end A is confined to move along the smooth circular bar of radius 3√2 ft. End B rests on the floor, for which the coefficient of kinetic friction is μ = 0.4. If the bar is released from rest when = 30°, determine the angular acceleration of the bar at this instant.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.
The 2.5-kgkg rod ACBACB supports the two 4.1-kgkg disks at its ends. If both disks are given a clockwise angular velocity (ωA)1=(ωB)1=4.6rad/s(ωA)1=(ωB)1=4.6rad/s while the rod is held stationary and then released, determine the angular velocity of the rod after both disks have stopped spinning relative to the rod due to frictional resistance at the pins AA and BB. Motion is in the horizontal plane. Neglect friction at pin CC.
The 10-kg uniform cylinder is pin supported at its center O. The square isacted upon by a constant force F = 10N and a constant couple moment M = 10 Nm.If the disk starts from rest, determine1) The reactions at the pin O and the angular acceleration of the disk2) The number of revolutions it must take to attain an angular velocity of 10 rad/s
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
The 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is μk = 0.13. The radius of gyration about the mass center is kG = 0.22 m Determine the angular velocity of the spool, measured clockwise, when t = 7 s after it is released from rest. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise
The smooth surface of the vertical cam is defined in part by the curve r =(0.2 cos θ + 0.3) m. The forked rod is rotating with an angular acceleration of 2rad/s^2, and when θ = 45° the angular velocity is 6 rad/s. Determine the force the camand the rod exert on the 2-kg roller at this instant. The attached spring has a stiffnessk = 100 N/m and an unstretched length of 0.1 m.
The man tries to reposition the 50 kg refrigerator in his kitchen by pushing it from rest with a force P = 170 N, inclined 30° from the horizontal at 1.60 m from the floor. The coefficient of non-sliding friction between the floor and the refrigerator is μs = 0.40.After pushing, the refrigerator started to tip. Which of the following quantities is ZERO at the instant described in the problem?a. friction at Ab. body's angular accelerationc. body's angular velocityd. the acceleration of mass center G Which of the following values is closest to the magnitude of the angular acceleration of the refrigerator?a. 7.57 rad/s^2b. 2.50 rad/s^2c. 1.892 rad/s^2d. 1.877 rad/s^2
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.
5. The 25-kg block AA is released from rest.
The drum, with radius R = 1.9 m, is given an initial counterclockwise angular velocity ω0. The drum is kept from rolling towards the left by a smooth vertical slot acting on a thin rod which passes through its centre. A vertical force (where C = 38, k = 1.7 and t denotes time in seconds) is being applied to a cord wrapped around the inner hub, with radius r = 0.7 m, of the drum. If the frictional coefficient is μk = 0.62 and the change in the angular momentum about O is ΔHO = 238 kg.m2/s (counterclockwise) during the first 2.3 seconds, determine the mass of the drum. (The mass of the cord and the thin rod may be regarded as negligible.) a)214.2 kg b)68.28 kg c)19.83 kg d)109.6 kg e)69.86 kg
The 7.5-lb disk A has a radius r A = 6 in. and is initially at rest. The 10-lb disk B has a radius r B = 8 in. and an angular velocity w0 of 900 rpm when it is brought into contact with disk A. Neglecting friction in the bearings, determine (a) the final angular velocity of each disk, (b) the total impulse of the friction force exerted on disk A.
15-102. The two spheres each have a mass of 3 kg and are attached to the rod of negligible mass. Determine the time the torque M = (8t) N·m where, is in seconds, must be applied to the rod so that each sphere attains a speed of 3 m/s starting from rest