FINAL ACTIVITY 1. A tension test was performed on a steel specimen having an original diameter of "N" and a gage length of "L" A. PROPORTIONAL LIMIT B. MODULUS OF ELASTICITY C. YIELD STRESS AT 0.2% OFFSET D. ULTIMATE STRESS E. NOMINAL RUPTURE STRESS PLOT THE STRESS-STRAIN DIAGRAM manually AND DETERMINE THE FOLLOWING MECHANICAL PROPERTIES. LOAD (kip) Elongation LOAD (kip) Elongation (in) (in) 0 0 20.0 0.100 1.5 0.0005 21.5 0.28 4.6 0.0015 19.5 0.40 8.0 0.0025 18.5 0.46 11.0 0.0035 17.2 0.50 11.8 0.0050 16.8 0.57 11.8 0.0080 15.1 0.63 12.0 0.0200 14.9 0.65 16.6 0.0400 Use a scale of 1in = 10ksi and 1in = 0.025 in/in. Show your complete solutions.

FINAL ACTIVITY 1. A tension test was performed on a steel specimen having an original diameter of "N" and a gage length of "L" A. PROPORTIONAL LIMIT B. MODULUS OF ELASTICITY C. YIELD STRESS AT 0.2% OFFSET D. ULTIMATE STRESS E. NOMINAL RUPTURE STRESS PLOT THE STRESS-STRAIN DIAGRAM manually AND DETERMINE THE FOLLOWING MECHANICAL PROPERTIES. LOAD (kip) Elongation LOAD (kip) Elongation (in) (in) 0 0 20.0 0.100 1.5 0.0005 21.5 0.28 4.6 0.0015 19.5 0.40 8.0 0.0025 18.5 0.46 11.0 0.0035 17.2 0.50 11.8 0.0050 16.8 0.57 11.8 0.0080 15.1 0.63 12.0 0.0200 14.9 0.65 16.6 0.0400 Use a scale of 1in = 10ksi and 1in = 0.025 in/in. Show your complete solutions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
a tensile test is conducted for a metal wire which has a diameter of 4.7 the maximum recorded force was 3500N. Thus UTS point is :-??
Bar of steel, (yield strenght Sy = 559 MPa) is subjected to the following stresses; σx = 176 MPa , σy = 107 MPa , τxy = 222 MPa Using the Maximum Shear Stress Theory (MSS) determine the factor of safety and check is the bar will fail or not.
38)A tensile test specimen has a gage length=3.0 inches and a diameter= .75 inches. Yielding occurs at a load of 38000lbs. The corresponding gage length=3.0103 inches (neglect the .0.2% yield point). The maximum load of 54000lbs i9s reached at a gage length =3.453 inches. Determine the tensile strength (Round to the nearest whole ksi)
A steel cylinder (Est = 200 GPa and G = 79 GPa) undergoes an azial compression in which its diameter increases from 10 mm to 10.045 mm. If its final length is 123.00 mm, what was its original length?
The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the propotional limit, modulus of elasticity (i.e the slope of the initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percent reduction area. TENSILE-TEST DATA Load(kN) Elongation(mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a steel alloy that has a yield stress of 340 MPa. The internal pressure is 1.5 MPa. 1. Calculate the tangential stress in the cylinder in MPa. 2. Calculate the longitudinal stress in the cylinder in MPa. 3. Calculate the allowable pressure in MPa if a factor of safety of 2.0 with respect to yield is required. Kindly answer all numbers with complete solution. Needed ASAP
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?
A 10000N tensile force is used to pull a cylindrical rod with an initial diameter of 2 cm. During the pull, the rod's diameter decreases to 1.8 cm. What is the true stress?i ll rate. S
7.10 A rigid bar is suspended by three equally spaced wires of equal length. Theouter wires are steel and are 2 mm in diameter, the centre wire is copper andis 5 mm in diameter. If the weight of the rigid bar is 2,25 kN, calculate the loadcarried by each wire. If the temperature of the system is now raised by 90 °C, what will the magnitude and nature of the resultant stresses set up in the steeland copper wires be. (Let EST = 200 GPa; Ecu = 100 GPa; aST = 12 x 10_6/°C;acu = 18 x 10-6/°C?)
A semi-elliptical spring 800mm long has eight leaves, two of which are full length. Theleaves are 8mm thick and 60mm wide each. It is desired to replace this spring by a helicalcoil spring of 100mm mean diameter and of such nature that for any load it will have thesame induced stress and same deflection as the leaf spring. What should be the diameter ofthe wire?
10.3. Consider the state of stress shown below that exists at a location within a component made up ofa brittle material, where this brittle material has tensile and compressive ultimate strengths ofσ UT = 170 MPa and σ UC = 850 MPa, respectively. Has the material failed at this location in thecomponent? Please include a free body diagram.