18. A solid cylinder of mass 5 kg and radius R = 0.15 m rolls without slipping on a horizontal surface and is accelerated to the right by a constant force F of magnitude 6 N that is applied at the cylinder by a massless rope as shown in the below figure. Find a) the magnitude of the acceleration of the center of mass of the cylinder, b) the magnitude of the frictional force on the cylinder. (Rotational inertia of a solid cylinder about central axis, I = 1/2 MR?.) R P.

18. A solid cylinder of mass 5 kg and radius R = 0.15 m rolls without slipping on a horizontal surface and is accelerated to the right by a constant force F of magnitude 6 N that is applied at the cylinder by a massless rope as shown in the below figure. Find a) the magnitude of the acceleration of the center of mass of the cylinder, b) the magnitude of the frictional force on the cylinder. (Rotational inertia of a solid cylinder about central axis, I = 1/2 MR?.) R P.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 27P: A solid cylinder of radius 10.0 cm rolls down an incline with slipping. The angle of the incline is...

See similar textbooks

Similar questions

A constant torque is applied to a rigid body whose moment of inertia is 4.0kgm2 around the axis of rotation. If the wheel starts from rest and attains an angular velocity of 20.0 rad/s in 10.0 s, what is the applied torque?
A soccer player extends her lower leg in a kicking motion by exerting a force with the muscle above the knee in the front of her leg. She produces an angular acceleration of 30.00 rad/s2 and her lower leg has a moment of inertia of 0.750kg-m2 What is the force exerted by the muscle if its effective perpendicular lever arm is 1.90 cm?
What force must be applied to end of a rod along the x-axis of length 2.0 m in order to produce a torque on the rod about the origin of 8.0k Nm ?
A potters wheel moves uniformly from rest to an angular speed of 1.00 rev/s in 30.0 s. (a) Find its average angular acceleration in radians per second per second. (b) Would doubling the angular acceleration during the given period have doubled the final angular speed?
An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
Suppose a child gets off a rotating merry-go-round, Does the angular velocity of the merry-go-round increase, decrease, or remain the same if: (a) He jumps off radially? (b) He Jumps backward to land motionless? (c) He jumps straight up and hangs onto an overhead tree branch? (d) He jumps off forward, tangential to the edge? Explain your answers. (Refer to Figure 10.34).
A grinding wheel is in the form of a uniform solid disk of radius 7.00 cm and mass 2.00 kg. It starts from rest and accelerates uniformly under the action of the constant torque of 0.600 N m that the motor exerts on the wheel. (a) How long does the wheel take to reach its final operating speed of 1 200 rev/min? (b) Through how many revolutions does it turn while accelerating?
A solid cylinder of radius 10.0 cm rolls down an incline with slipping. The angle of the incline is 30 . The coefficient of kinetic friction on the surface is 0.400. What is the angular acceleration of the solid cylinder? What is the linear acceleration?
Repeat Example 10.15 in which the stick is free to have translational motion as well as rotational motion.
An automobile engine can produce 200Nm of torque. Calculate the angular acceleration produced if 95.0 of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0-kg disk that has a 0.180-m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
Suppose a disk having massMtot and radius R is broken intofour equal parts (Fig. P13.10).What is the rotational inertia ofone-fourth of the disk aroundthe z axis shown? FIGURE P13.10
CHECK and THINK Our results give us a way to think about how a person might steer a unicycle. Consider the person, the unicycle, and the Earth as the system. No net torque acts on the system. Ignoring the motion of the Earth, Figure 13.37A shows the initial angular momentum of the system with the unicycle in motion: Li=Ltire. The person leans to his left so that the angular momentum of the tire rotates downward. The total angular momentum must still point to the right (Fig. 13.37B), so the angular momentum of the person must be upward to compensate. The persons angular velocity therefore points upward (parallel to his own angular momentum), and he is able to make a turn. Another way to analyze this situation is to exclude the Earth from the system and calculate the torque done by gravity. This approach is left as a homework problem. FIGURE 13.37 C Reanalyze the unicycles motion in Example 13.15 (page 382). This time, leave the Earth out of the system and explain how the torque exerted by gravity causes the unicycle to turn. Your explanation should involve a diagram.