18. Compute the velocity of a fluid which would flow from the base of a water storage tank where the level of the surface is 35 ft above the ground. Consult Fig. 3-17. 35 Figure 3-17 Problem 18. 19. In Problem 18, if the hole in the base of the tank has a 3-in. I.D., and there are no friction losses, what flow rate could be expected?

18. Compute the velocity of a fluid which would flow from the base of a water storage tank where the level of the surface is 35 ft above the ground. Consult Fig. 3-17. 35 Figure 3-17 Problem 18. 19. In Problem 18, if the hole in the base of the tank has a 3-in. I.D., and there are no friction losses, what flow rate could be expected?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the figure shown, the flow rate is 0.05 m'/s, determine: (a) pressure at A and B, (b) the machine in this system, is it pump or turbine? Explain it by calculations. [Neglect minor losses).
Aa certain hydro-power station has a head of 500m between the upper and lower reservior. A. Determing the approach velocity of water as it enters the turbine ; B. If the volume flowrate is 60cumec, what is the diameter of the penstock; and C. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity approach and the corrected diameter of the penstock required
find the diameter of pipe of length 2500m when rate of flow of water through pipe is 0.25m cube/sec and head lose due to friction is 5m . take C=50 in chezy's formula
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)
Water at 10°C is flowing from point A to point B through the fabricated section shown below at the rate of 0.37 m3/s. If the pressure at A is 66.2 kPa, calculate the pressure at B. answer should be 34.9 kPa
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
2500kW power is generated shown in the Figure with a water flowrate of 20 m3/s. The head loss for the entire flow is 2.5m. (a) Find the pressure difference P1 - P2 across the turbine. (b) Find h You can neglect the head loss between point 1 and 2.
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
A certain hydro-power station has a head of 500m between the upper and lower reservoir . a. Determine the approach velocity of water as it enters the turbine; b. If the volume flow rate is 60 cumec, what is the diameter of the penstock; and c. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity of approach and the corrected diameter of the penstock required.
The 11-in Bell and Gossett pump is tobe scaled up to provide, at best efficiency, ahead of 250 ftand a flow rate of 3000 gal/min. Find the appropriate(a) impeller diameter; (b) speed in r/min; and (c) horsepowerrequired.
The 20mm diameter commercial steel pipe, 30 m long is used to drain a water tank. The water level in the tank is 3 m above the exit of the pipe. Neglect minor losses and assume f-0.018. a.) What is the pressure head at the exit of the pipe? b.)What is the head velocity of the pipe c.) What is the discharge at the exit of the pipe in liters per second d.)headloss