18.A venture meter is a device that uses a constriction in a flow system to measure the velocity of flow, Figure 12 illustrate one type design. If the main pipe section is a standard hydraulic copper tube having a 100-mm outside diameter x 3.5-mm wall thickness, compute the volume flow rate when the velocity there is 3.0 m/s. Then, for that volume flow rate, specify the required size of throat section that would make the velocity there at least 15.0 m/s.

18.A venture meter is a device that uses a constriction in a flow system to measure the velocity of flow, Figure 12 illustrate one type design. If the main pipe section is a standard hydraulic copper tube having a 100-mm outside diameter x 3.5-mm wall thickness, compute the volume flow rate when the velocity there is 3.0 m/s. Then, for that volume flow rate, specify the required size of throat section that would make the velocity there at least 15.0 m/s.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter16: Gas Tungsten Arc Welding Equipment, Setup, Operation, And Filler Metals

Section: Chapter Questions

Problem 21R: Why must the tube of a flow meter be vertical?

See similar textbooks

Similar questions

Water at 15°C is flowing in a 3 inch horizontal Schedule 40 steel pipe at a pressure of 102 kPa. The pipe reduces to a 1.5 inch Schedule 40 steel pipe. What is the flow rate if pressure in the 1.5 inch pipe is 99.8 kPa?
Q.1 Water is flowing through a 6” dia corrugated steel pipe. An energy loss of 2ft of head occurs over a length of 100ft . Compute the volume flow rate and velocity at design value of Ch?
A flow meter is attached to a hydraulic line that measures 8 gal/min. The line has an inside diameter of 1.5in. What is the flow rate measured in in3/min at the meter?
Calculate the resistance coefficient K for a check valve swing type placed in a 6 inch schedule 40 steel pipe if water at 100º F flowing with a velocity of 10 ft/s
In Applied fluid mechanic, chapter 8 problem 8.21, can someone explain to me how to solve step by step? The question is A system is being designed to carry 500 gal/min of ethylene glycol at 77 F at a maximum velocity of 10 ft/s. Specify the smallest standard Schedule 40 steel pipe to meet this condition. Then for the selected pipe compute the Reynolds number for flow.
A flow meter is attached to a hydraulic line that measures 8 gal/min. The line has an inside diameter of 1.5in. What is the inside area of the line
A standard short tube, 4 in. in diameter, discharges water under a head of 20 ft. What is the discharge in cubic feet per second if Cd=0.829?
Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K copper tube if the volume flow rate of water at 60'F is Q 0.5 gal/min. Use increments of 0.05 in and include the velocity at the centerline. please be through and provide all calculus and graphs/tables
Show all problem solution's steps. Direct formula substitution solutions will have NO CREDIT POINTS. 1.A 50 mm Venturi meter (C = 0.96) is installed in a 100 mm diameter horizontal pipe carrying oil having a specific gravity of 0.82. If the recorded actual flow in the Venturi meter was 15 liters per second, what could have been the deflection of water in the differential manometer connected between the inlet and the throat? Determine the headloss in the Venturi meter. A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The lost head in the nozzle is 25% of the velocity head in the jet. If the pressure at the base of the nozzle is 625 KPa: compute the discharge in m3/min; the maximum horizontal range to which the stream can be thrown; the maximum vertical reach, and the diameter of the jet at a point two-third of the maximum vertical reach from the tip of the nozzle. Neglect air resistance.
Inorder to achieve a liquid flow rate of 500 gal/min with a maximum pressure difference of 42 psi, calculate the value of valve flow coefficient. The specific gravity of liquid is 1.3.
Hydraulic fluid flows at velocity of 200 in/min through a conduit with an internal diameter of 2 inches. Determine the flow rate in GPM. Be aware of your units!
Specifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe in the one inch branch is 8 ft. Brine (sg=1.04, m=10-3Pa*s) flows at 250gpm through the entrance at point A. Assume fully turbulent flow in both branches (f=ft). Pipes are standard Schedule 40 steel pipes. Assume the globe valve is partially shut so its equivalent L/D is 1000. For Part 1 of this project, you are tasked with determining the following: The flow rate in both branches The pressure drop in both branches The overall resistance coefficient