Question 8 Describe the possible flows through the network of water pipesshown in figure where flow is mentioned in litres per minute.

At each node, we write out the equation that represents the conservation offlow there. We then…

Answered: Question 8 Describe the possible flows…

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter16: Gas Tungsten Arc Welding Equipment, Setup, Operation, And Filler Metals

Section: Chapter Questions

Problem 21R: Why must the tube of a flow meter be vertical?

See similar textbooks

Similar questions

What is the ratio of the average velocity to maximum velocity for water flowing in a 1” schedule 40 pipe? Assume Laminar flow.
The wall thickness of a pipe is referred to as the pipe's __________.
In the branched-pipe system shown in Fig. 12.9,1350 gal/ min of benzene (sg 0.87) at 140°F is flowing in the 8-in pipe. Calculate the volume flow rate in the 6-in and the 2-in pipes. All pipes are standard Schedule 40 steel pipes.
If the Friction Factor for a galvanized iron pipe is 0.03 and the Reynolds Number is 2∗104 then what is the pipe diameter in inches?
Draw and identify commonly used flowsheet (e.g. existing lines, underground lines, gate valve, check valve, etc.) and equipment (e.g. boiler, heat exchanger, centrifuge, agitator, etc.) symbols in presenting a process scheme.
A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe.
18.A venture meter is a device that uses a constriction in a flow system to measure the velocity of flow, Figure 12 illustrate one type design. If the main pipe section is a standard hydraulic copper tube having a 100-mm outside diameter x 3.5-mm wall thickness, compute the volume flow rate when the velocity there is 3.0 m/s. Then, for that volume flow rate, specify the required size of throat section that would make the velocity there at least 15.0 m/s.
Q.1 Water is flowing through a 6” dia corrugated steel pipe. An energy loss of 2ft of head occurs over a length of 100ft . Compute the volume flow rate and velocity at design value of Ch?
Answer the following: a.) Friction factorb.) Determine the pressure drop per meter of pipe
Show in Figure 1 is the water flow system. The velocity head difference is . Volume flow rate is . The heights are and , respectively. The power output from the motor is , . The energy added by the pump is . The energy loss between point 1 and 2 is . 3) Select the correct expression of the pressure head difference between point 1 and 2 ___________
A dam supplies water for a community as shown in Fig. 1. Also, a turbine is used before the storage reservoir to produce electricity. The system is designed to provide 2620 L/s of water at 20°C. The pipe system consists of 76 m of pipe and two 90° elbows. All pipe is 508 mm diameter, which made from cast iron. Figure 1: Schematic diagram of task 1. - Calculate the average velocity of water in the pipe? - Determine the Reynolds number in the pipe system and the significance of this Information? - Using Bernoulli’s equation, find the water pressure at point C? - Determine the head losses accumulated by the fluid when flowing in the pipeline? - Calculate the energy that the fluid will lose after passing through the turbine by applying the energy equation? Page 5 of 8 5 - If the used turbine converts only two-thirds of the energy that the fluid will lose after passing through the turbine, what is the efficiency of this turbine? - Identify the most common water turbines and the limitations…
The measured flow rate of water through a 20 mm diameter pipe is 75 L/min. What is the Reynolds (Re) number?

SEE MORE QUESTIONS

Recommended textbooks for you

Welding: Principles and Applications (MindTap Cou…

Mechanical Engineering

ISBN:

9781305494695

Author:

Larry Jeffus

Publisher:

Cengage Learning

Refrigeration and Air Conditioning Technology (Mi…

Mechanical Engineering

ISBN:

9781305578296

Author:

John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:

Cengage Learning

Welding: Principles and Applications (MindTap Cou…

Mechanical Engineering

ISBN:

9781305494695

Author:

Larry Jeffus

Publisher:

Cengage Learning

Refrigeration and Air Conditioning Technology (Mi…

Mechanical Engineering

ISBN:

9781305578296

Author:

John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Question 8 Describe the possible flows through the network of water pipes shown in figure where flow is mentioned in litres per minute.