Electrical Machine Lab. Single-PhaseInduction Motor (Split Phase)A.C.M.Supply1-0Fig (2)1_Plot the relationship between the torqueand the speed for single-phase inductionmotor (split phase).2-lf the auxiliary winding is unconnected,what is difference on the running in the cct„shown in fig.(2).3- What is the main difference between themain and auxiliary windings ? and how wecan obtain on it ?4. At 75% from the rated speed in themotor we isolated the auxiliary windingfrom the cct why?5_What is the pulse torque ? can be reducingthe effect of this torque ? how?

“Since you have asked multiple question, we will solve the first question for you. If you want any…

Answered: 1_Plot the relationship between the…

Engineering

Electrical Engineering

1_Plot the relationship between the torque and the speed for single-phase induction motor (split phase).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the given electromechanical system with all parameters in SI units, the motor used develops 50 Nm of torque at 3000/pi in rpm when 15 volts applied. It is stalled at this DC voltage with 150 Nm of torque. The armature inertia is 5 kg.m2 and damping is 2 N.m.s/rad. What is the equivalent load damping DL at the N3 port
A 12-phase ∆-connected 3200 V (line-to-line), 12,000 kW, 50 Hz, twelve-polesquirrel-cage induction drive is designed for electric vehicle use. The drive has thefollowing equivalent parameter values in Ω/phase referred to the stator:R1= 0.697 Ω R2= 0.328 Ω Rm1 = 226 ΩX1 = 0.549 Ω X2 = 0.456 Ω Xm1 = 31.573 ΩThe total friction, windage, and core losses are assumed to be constant at Plosses=1156 W, independent of load.a)Draw the equivalent circuit for this drive and show the relevant parameters onthe circuit.For a slip value of s = 0.032 and using the above equivalent circuit parameters,determine: b) The stator current and the power factor c) The synchronous speed and the rotor speed for this drive d) The torque generatede) The input power for this operating conditionf) The efficiency when operated at rated voltage and frequencyg) Considering the design of this motor, state if it is possible to start this drive witha slip ring starter. Give reasons to justify your answer. just need answer…
A 12-phase ∆-connected 3200 V (line-to-line), 12,000 kW, 50 Hz, twelve-polesquirrel-cage induction drive is designed for electric vehicle use. The drive has thefollowing equivalent parameter values in Ω/phase referred to the stator:R1= 0.697 Ω R2= 0.328 Ω Rm1 = 226 ΩX1 = 0.549 Ω X2 = 0.456 Ω Xm1 = 31.573 ΩThe total friction, windage, and core losses are assumed to be constant at Plosses=1156 W, independent of load.a)Draw the equivalent circuit for this drive and show the relevant parameters onthe circuit.For a slip value of s = 0.032 and using the above equivalent circuit parameters,determine:b) The stator current and the power factorc) The synchronous speed and the rotor speed for this drived) The torque generatede) The input power for this operating conditionf) The efficiency when operated at rated voltage and frequencyg) Considering the design of this motor, state if it is possible to start this drive witha slip ring starter. Give reasons to justify your answer
Find the speed and torque at the steady-state for the drive has the following parameters: Electric Motor: A 220 V, 13 A and Kϕ=2.5 (V. sec) DC separately excited motor has Ra= 0.8 Ω , and Rf=Rf= 10 Ω . Conveyors: TL=175 TL=175 N.m Find the steady-state operating point, the speed(N) and torque(T). Determine the steady-state for the equilibrium point.
A 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44ohms. at rate load, the driving engine develops 62.26hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses and Efficiency on the DC MACHINE) (I need a clean solution ma'am/sir. Thank you do much)
A 60 Hz, four-pole 480 V, three-phase, wye-connected induction machine has the following parameters: R1 = 0.2Ω R2’ = 0.3Ω XT = 12Ω The motor is loaded with a unidirectional constant-torque of 40 Nm. A counter current braking is performed on the motor, by interchanging phases A and B. Determine The motor speed at the new steady-state point The operating mode at the new steady-state point. Efficiency of the machine at the new steady-state pint. (Assume negligible core and mechanical loses.)
A series DC machine with the armature winding resistance Ra=2Ω and the field windingresistance Rf=5Ω is mechanically coupled to the load with linear torque-speedcharacteristics that can be approximated by the following equation: Tl(ω)=k·ω+T0 where k=-2Nm/(rad/s) and T0=200 Nm. The motor constant Kf is equal to 0.22[Nm/A^2] also[Vs/(A·rad)]). The motor is supplied from a 250VDC source. a) Calculate all possible operating points and determine the stability of each operatingpoint
A 12-phase ∆-connected 3200 V (line-to-line), 12,000 kW, 50 Hz, twelve-pole squirrel-cage induction drive is designed for electric vehicle use. The drive has the following equivalent parameter values in Ω/phase referred to the stator: R1= 0.697 Ω R2= 0.328 Ω Rm1 = 226 Ω X1 = 0.549 Ω X2 = 0.456 Ω Xm1 = 31.573 Ω The total friction, windage, and core losses are assumed to be constant at Plosses=1156 W, independent of load.a)Draw the equivalent circuit for this drive and show the relevant parameters on the circuit.For a slip value of s = 0.032 and using the above equivalent circuit parameters, determine: b) The stator current and the power factorc) The synchronous speed and the rotor speed for this drived) The torque generatede) The input power for this operating conditionf) The efficiency when operated at rated voltage and frequencyg) Considering the design of this motor, state if it is possible to start this drive with a slip ring starter. Give reasons to justify your answer
A separately-excited DC generator with compensating windings (Fig. 1), that is, effects of armature reaction is negligible, rated at 10 kW, 100 V has a magnetization curve shown in Fig. 2. Assume generator is driven at 1600 RPM. The generator shown in Fig. 1 is rewired as a self-excited shunt DC generator and Radj adjusted to 10 Ω and generator speed is set at 1600 RPM. Ignoring the effects of armature reaction, answer the following questions: a. Assuming voltage buildup is successful, what is the no-load terminal voltage of this generator? (Answer in zero decimal places) b. If the generator is supplying 40 A to a load, what would be its terminal voltage in volts? (Answer in 2 decimal places). Note that your answer in Question A is your EA. c. What would be the total electrical losses in watts incurred by the generator in Question B? (Answer in zero decimal places) d. If mechanical losses in Question 6 is 500 watts, what is the efficiency of this generator in %? (Answer in 2 decimal…
A dc motor develops 55 N-m of torque at a speed of 600 rad/s when 12 volts are applied. It stalls out at this voltage with 100 N-m of torque. If the inertia and damping of the armature are 7 kg-m2 and 3 N-m-s/rad, respectively, find the transfer function, G(s)=θL(s) / Ea (s), of this motor if it drives an inertia load of 105 kg-m2 through a gear train, as shown in Figure 2 below.
a dc shunt generator supplies a load of 10kW at 250V calculate the induced emf,if the armature resistance is o.5ohm and the shunt field resistance is 100ohm
A 6-phase ∆-connected 1600 V (line-to-line), 150 kW, 50 Hz, six-pole induction driveis used in an electric car. The drive has the following parameter values in Ω/phasereferred to the stator:R1 =0.334 Ω R2 =0.168 Ω Rm1 = 125 ΩX1 = 0.273 Ω X2 = 0.287 Ω Xm1 = 16.78 ΩThe total friction, windage, and core losses may be assumed to be constant at Prot =773 W, independent of load. For a slip value of s=0.015: b ) Compute the speed, output torque, power and stator current d) Calculate the efficiency when the motor is operated at rated voltage andfrequency. answer：b) n= 985 rpm; Torque T= 1.18 x104 Nm; Power= 1.22 x106 W; Stator current I = 175.72 /32.79° (d) Efficiency = 86.4%