x Chapter-5B.pdfX Talevebapps/assessment/take/take.jsp?course_assessment id%=_12957_1&course_id=_18638_18content_id= 214533_1&cPA-Remaining Time: 40 minutos, 39 seconds.Question Completion Status:Qbesion7The fuel inputs per hr of plant-1 and plant-2 are given asF1 = 0.4P2 + 80P1 +240 OMR/hrF2 = 0.5P+ 60 P2 +300 OMR/hrDetermine the economic operating schedule corresponding cost generation if the total load is 360MW.Neglect the line losses and generator limits.P1 = 188.89P2 = 171.11Total Cost = 54,829.12 OMR I hrP1 = 189.89P2 = 170.11Total Cost = 52,629.12 OMR I hrP1 = 185.89P2 = 174.11Total Cost = 58,429.12 OMR / hrتنشيطNone

The total load is given as 360MW. So we have: P1+P2=360 (1) For economic load scheduling we…

1&course_id%3_18638_18&content_id3 214533 Remaining Time: 40 minutos, 39 seconds. v Question Completion Status: The fuel inputs per hr of plant-1 and plant-2 are given as F1 = 0.4P2 + 80 P1 +240 OMR/hr 2 = 0.5P+ 60 P2 +300 OMR/hr Determine the economic operating schedule corresponding cost generation if the total load is 360MW.Neglect the line losses and generator limits. P1 = 188.89 P2 = 171.11 Total Cost = 54,829.12 OMR I hr P1 = 189.89 P2 = 170.11 Total Cost = 52,629.12 OMR / hr P1= 185.89 P2 = 174.11 Total Cost = 58,429.12 OMR / hr None

1&course_id%3_18638_18&content_id3 214533 Remaining Time: 40 minutos, 39 seconds. v Question Completion Status: The fuel inputs per hr of plant-1 and plant-2 are given as F1 = 0.4P2 + 80 P1 +240 OMR/hr 2 = 0.5P+ 60 P2 +300 OMR/hr Determine the economic operating schedule corresponding cost generation if the total load is 360MW.Neglect the line losses and generator limits. P1 = 188.89 P2 = 171.11 Total Cost = 54,829.12 OMR I hr P1 = 189.89 P2 = 170.11 Total Cost = 52,629.12 OMR / hr P1= 185.89 P2 = 174.11 Total Cost = 58,429.12 OMR / hr None

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Briefly explain TNC-S earthing scheme as applied to earthing system design. (Hint: Support your answer with a well labelled diagram).
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:In a group of 3 motors, one draws 15 A the other draws 40 A, and the third 52 A. What size of the conductor in terms of ampacity may be used for the feeder circuit? 107 A 120 A 134 A 160 A
The block diagram in the figure shows the root locus of the system. draw?
Airframe Electrical System Question: What things should be included in the identification stamp found along the electrical wires length? (Source: FAA AC 43.13-1B/2B)
Airframe Electrical System Question: Name five areas in an aircraft that are considered "EWIS" areas. (Source: FAA AC 43.13-1B/2B)
Please answer ASAP for like Please Asap Please
Do this root locus problem using manual calculations, please include the steps Please answer in typing format please ASAP for the
Question bRam Full explain this question very fast
(c) Draw a circuit diagram to represent a TN-C-S earthing system and briefly explain its advantages and disadvantages. (d) Briefly explain how to estimate the height of air termination of a lightning protection system network using the rolling sphere method and protection angle method. (e) Briefly explain what is meant by Ground Potential Rise (GPR) and explain why an animal like cow would not be adequately protected against GPR. Note : answer all or else dnt attempt the question
How would you draw the root locus for this system?
No plagarism please! Correct and detailed answer will be Upvoted else downvoted and reported. Thank you!
Please show how to calculate the loads, give the size of wire and circuit breaker size per stall and for feeder with the given values in the table. Assume its only 1-phase, and there is no given of p.f., and the country should be based on is Philippines. Upvote will be given for sure in the end. Thank you so much! Just want to learn how does the Schedule of Load works.