1C) Simply supported beam has pin and supports. Da. cable O b. fixed D c. roller O d. spring

Q: d AB (G= 39 GPa). Eac

A: answer= 17.899 deg

Q: ever beam with appropr

A: A cantilever beam is a beam having one end is fixed and other end is free. The diagram of cantilever…

Q: Define the term 'weight'.

A: Weight is the amount of downward force that is applied by gravity to any object in its gravitational…

Q: What is the springs free length(ft)?

A:

Q: Mechanical advantage is the ratio of effort to load. a) True b) False

A: Mechanical advantage is the ratio of effort to load. a) True b) False

Q: A beam extending beyond the support is called (a) Simply supported beam (c) Overhanging beam (b)…

A: When a beam is supported by support at both end is called simply supported beam .   When a beam is…

Q: The students are required to differentiate the following terms using the figures along with the…

A: (1) Consider the diagram shown below for simply supported and cantilever beam.

Q: A simply supported beam is loaded as shown in the following schematic: P.

A:

Q: 9. A cantilever is a beam whose Both ends are supported either on rollers or hinges One end is fixed…

A: Answer is option (b) One end is fixed and other end is free.

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: 2 B

A: To-Find:- Resultant at point C

Q: A frame is being raised on a pivot point. a crane lifts the frame and shows 315 165 at 45⁰. How much…

A:

Q: 300 lb B. Ao 20 in. 48 in.- 15 in.

A: Given dataLoad P = 300lb (vertically downwards)

Q: indoor design dry C and 25°C resp

A:

Q: 1. Which sprinting techniqu uds effective: flexing the knee swing leg more during the

A: Sprinting technique is nothing but the forward momentum given focusing on the adjustments in your…

Q: FOR fixed support , the number of unknowns are ?

A: FOR fixed support, the number of unknowns are? 2 3 1 4

Q: M- mass that can what is the maximum mass be hung fremy the keep?

A:

Q: In a simply supported beam, the deflection is at its supports

A: Ans-b. zero

Q: 5 kip/ft 15 kip ft 15 kip ft B 6 ft 10 ft 6 ft

A:

Q: Facing operation is performed on? A. Drilling machine. B. Sawing machine. C. Milling machine. D.…

A: Facing operation is performed on lathe machine.

Q: Pulleys - Cords Stopper Container Water Stopcock Ball Float

A:

Q: Pa P, 40°- 2 ft -25° P1 each item to a choice:

A:

Q: Create a Load Duration Curve based on the given load

A: The given data for time of day and load is as  below:

Q: Figure 1 of 1 |2P A -2 ft- -2 ft- d 2 in.

A: find the maximum magnitude of load P.

Q: Provide a floor plan of a common or general Bread Manufacturing Plant.

A: given; Provide a floor plan of a common or general Bread Manufacturing Plant.

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: In sectional view, mechanical fasteners like bolts, screws, nuts are represented as___. a. Sectioned…

A: Sectional View

Q: 0 HOME WORK.. HOME WORK DRAW,SECTION A-A +TOP VIEW +LEFT SIDE VIEW 50 R30 A RI5 RIO

A: TOP VIEW :-

Q: The amount of deflection of the beam depends upon

A:

Q: The specific weight of material is

A: OPTION C is the correct answer

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: Plzz solve I give you rating

A: Given unidirectional laminate, vf=Fibre volume fraction=0.55Ef=Young's modulus of carbon fire=310…

Q: 1. A vessel has cargo hold capacity of 4312 m3 and shall load grain with SF 1.3 m3 /ton. How many…

A: Question 1: Volume capacity of cargo = V = 4312 m3 Stowage factor = SF = 1.3 m3/ton   To find the…

Q: for beam below what is the correct * BMD 5 kN, 2 kN/m 10 m -10 50

A:

Q: Confined

A: given Identify actions required before approving Start of Work in a Confined Space.

Q: Draw diagrams (this requires some thought) that show to lift a heavy box, a beam can be used as a:…

A: Solution:

Q: List 5 criteria of a windmill.

A: A windmill is a mechanical device or a engine that is used to converts the winds energy into…

Q: for beam below what is the correct BMD 5 kN, 2 kN/m 10 m

A:

Q: .Q21 The forces do not cause rotation

A: The concurrent forces traverse through a similar point. It means that other forces balance each…

Q: 6 kip/ft 8 kip AB A 9 ft 4.5 ft 5 ft -

A:

Q: beam is simply supported at points, but also it projects beyond the supports. O a. fixed O b.…

A: Beams: The structural members that have uniform cross-sectional areas throughout their length are…

Q: Describe the steps how to solve all reaction at the support

A: The diagram of truss is given as,

Q: rd frame and dr.

A:

Q: b. +メく + be=30 cm; b, =11 cm; b, = 1Dcm he bi = 22 cm; hz= 20cm; hg =17cm In=? Ymar=?

A: Divide this shape into three parts 1st part is hatched part 2nd part is (b3*h2) 3rd part is (b4*h3)…

Q: Prob 3: Form lumbers are: 2 x 2 3 pcs 5 pcs 12 pcs 2x 4" x 12 cost is $ 52/6d ft, if How much will…

A:

Q: Which side will go down? A! 5m 5m 10KG 5KG B

A:

Q: Define the term Angle of Repose

A: The slope of cut and fill at the excavation site which is measured in feet of horizontal to feet of…

Q: Create a Variable Load curve based on the given load

A: Draw the variable load curve by using given data.

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.