Define the term Angle of Repose

Q: Which of the following is not considered as a lower pair

A: 1. Option (c)  Roller pair  is correct option. Explanation: As we know that line and point contact…

Q: Explain with Sketch: (a) Anchor cable marking. (b)Bitter end of the anchor chain.

A: (a) Anchor cable marking. (b)Bitter end of the anchor chain. Here the explanation with diagram of…

Q: Sommerfeld number of the bearing

A: Given;A hydrodynamic  journal bearing is subjected toLoad= 2000 NRotational speed=2000 rpm bearing…

Q: The inner and outer surfaces of a cyl nd

A: K = 2 W / mk    r1= 1 cm , t1 = 300 degree    r2 = 2 cm , T2 = 100 degree    The diagram has been…

Q: Describe Scavenging

A: IC engine completes one power stroke in four strokes. Intake of A/F mixture Compression Power…

Q: 2. It is used to loosen or tighten screws that have a star-like depression on the top, a feature…

A: Since you have posted a multiple independent questions in a single question. We will solve the first…

Q: IS ading edg

A:

Q: Sketch the proper end shape of a soapstone that is to beused for marking metal.

A: The design of the work metal is marked with soapstone & chalk line to ensure appropriate…

Q: ust be from the origin. 70 mm mm 60 mm 10 mm

A: Area symbol area mm2 x̄(mm) ȳ (mm) A x̄(mm3) A ȳ (mm3) A1 40*15=600 -62.5 27.5 -37500…

Q: rad). Determine the wire diameter and the number of active

A: Given: D=18 mm Fos=2 Mb=250 Nmm k=3 Nmm/rad σyt=0.6σut To determine: Diameter of the wire no of…

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: rance between an alloy that failed at a lo

A: (e) In materials science, weariness is the debilitating of a material brought about by cyclic…

Q: What is its diameter-to-length ratio for

A:

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: Dad with an angle of 10° and radius

A:

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: Draw the free body diagram Always use 3 decimal place

A:

Q: Define and explain hookes law

A:

Q: Figure 1 of 1 |2P A -2 ft- -2 ft- d 2 in.

A: find the maximum magnitude of load P.

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: troid, ỹ on axis x'- x ' for the parts cross-sectic

A:

Q: min. Cylinder wall thickness for safe design

A: Given; Thin cylinder with an internal radius=100 mmor, d=2r           =100×2           =200…

Q: What is the other name for the short column?

A:

Q: (a) the melting temperature for ic

A: the melting temperate of ice at 0.01 atm = 10C Boiling temperature of ice at 0.01 atm = 7 0C

Q: 2 kip/ft 50 kip - ft 50 kip · ft B 10 ft 20 ft 10 ft

A:

Q: an der Waal for I cross links.

A: In the above question all the options are incorrect Stiffness of thermosets are high

Q: Calculate Degree of freedom for the following figures.

A: (i) Degree of freedom is calculated by using the formula DOF=3l-1-2j-h

Q: 1. Write the procedure for shaper process.

A: Shaper process is the process in which unwanted metal surface is removed by a single-point cutting…

Q: Is this for number 1 only?

A:

Q: Describe the limiting angle of repose. Provide equations and examples to support your point

A:

Q: When utilizing pins to assemble rigging components, the "grip" area of the pin is  A. diameter of…

A: Rigging pins are generally measured by the diameter and the grip length. Given diameter can be…

Q: Derive an expression for the height of Proell governor.

A: The answer is in next step

Q: is reduced icinal is

A:

Q: In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the…

A:

Q: Which of the following is the front ?view of the figure

A:

Q: Define Iron Stirrups

A: Given Stirrups To find Iron stirrups

Q: Types or Cran

A: There are various types of cranes are available on market on the basis of the requirement of the…

Q: A ball and a socket joint forms a

A: A ball and a socket joint is a form of synovial joint in which socket swivel around the fixed ball.…

Q: The cause of an induced angle

A: Solution ;

Q: If a washer has a 1” outside diameter and a .50” inside diameter, what is the distance between the…

A: Given data, D= 1 in.  d= 0.50 in.

Q: ɪꜱ ꜱᴜʙᴊᴇᴄᴛᴇᴅ ᴛᴏ ᴀ ᴛᴇɴꜱɪʟᴇ ꜰᴏʀᴄᴇ ᴏꜰ 400 ᴋɪᴘꜱ with 10 inch of diameter. ɪꜰ ᴛʜᴇ ᴘᴏɪꜱꜱᴏɴ'ꜱ ʀᴀᴛɪᴏ ɪꜱ…

A:

Q: A steel bar of c

A: 1.2125mm

Q: Differentiate enery and force

A: energy is defined as the amount of work that can be performed by force and units of the energy is…

Q: A rod consists of two parts that are made

A: Kindly refer attached files.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.