2-94 Four forces are applied at a point in a body asshown in Fig. P2-94. Determine the magnitude of the re-sultant R of the four forces and the angle e between ther-axis and the line of action of the resultant.F= 275 IbF = 300 lb60°20°2835F- 650 IbF = 750 lb

Given Data: The force F1 = 300 lb. The force F2 = 650 lb. The force F3 = 750 lb. The force F4 = 275…

Answered: 2-94 Four forces are applied at a point…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A man on the wire singing "Man on a Wire" while practicing for his circus show has reached the center of the rope, creating a dip on the center angled at 63.2 degrees. If the mass of the man is 49.55 kg and the tension force that can be handled by the wire is 449.77N, would the wire break? Show the tension caused by the man hanging on the wire.
A metal cylinder hangs from the ceiling through three cables attached as shown. If the tension in cable AD is 4.3 kN, what would be the (a) tension on cables AB and AC (b) weight of the cylinder Answer: T_AB=4.1667kN ; T_AC= 3.8250kN; W=9.71kN Kindky answer it with complete solution and with this format: Given Equation Solution
Mechanics of material Please answer Q3,4
How much work is done in forcing 50 ft3 of water through a 0.5-inch pipe if the difference in pressure at the two ends of the pipe is 15 lbs/in2? PLS DONT FORGET TO INCLUDE FREE BODY DIAGRAM Use the equation Work=(P1-P2) times change in Volume If POSSIBLE
tank holding oil (SG=0.90) with its top surface open to the atmosphere is shown below. determine the magnitude and line of action of (a) the horizontal component (Fh) and (b) the vertical component (Fv) of the resultant force (Fr) exerted by the curved surface BC on the fluid. The tank is 4m deep, 2m wide, and R=1.5m. (c) Determine the magnitude and line of action (angle of inclination relative to the horizontal) of the resultant force, Fr
A heavy crate rests on an inclined surface. Find the smallest force P required to keep the crate from sliding back down the inclined surface, given:Mcrate = 170 kg, μ = 0.2 θ = 20 °
Determine the absolute value of the force at point O in [N] ? m = 30 kg F=422 N w = 8 rad/s
A spring exerts a force of 17 lbf on a piston inside a piston cylinder device. The mass of the piston is 3.5 lbs and the cross sectional area of it is 0.00018 ft^2. Determine the pressure inside the piston cylinder device.
In the figure shown, the large piston on the left has a diameter of D1 = 9.00 cm.The small piston on the right has a diameter of D2 = 4.00 cm.A lever arm pivot is located a = 5.00 cm to the left of the small piston.A small cylinder hangs from the end of the lever arm a distance b = 25.0 cm to the right of the small piston.In the absence of friction, determine the weight of the cylinder on top of the large left piston which can be supported in equilibrium with the small mass (m = 0.350 kg)hanging from the far right lever arm.Provide a force vector diagram (free body diagram).
Datos: F1(KN)=5 F2(KN)=20 F3(KN)=10 L1(m)=4 H(m)=-5 I add the picture of the question
Gate AB (0.6-m × 0.9-m) is located at the bottom of a tank filled with methyl alcohol (SG = 0.79), and hinged along its bottom edge A. Knowing that the weight of the gate is 300 N, determine the minimum force that must be applied to the cable (BCD) to open the gate.
A. Three cable tensions T1, T2, and T3 act at the top of the flagpole. Given that the resultant force for the three tensions is R = 400 N downward, find the magnitude of the cable tension T3 in N. Answer: 220.34 B. Three cable tensions T1, T2, and T3 act at the top of the flagpole. Given that the resultant force for the three tensions is R = 400 N downward, find the magnitude of the cable tension T2 in N. Answer: 151.59 I need a solution

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

2-94 Four forces are applied at a point in a body as shown in Fig. P2-94. Determine the magnitude of the re- sultant R of the four forces and the angle e between the r-axis and the line of action of the resultant. F= 275 Ib F = 300 lb 60° 20° 28 35 F- 650 Ib F = 750 lb