2) A Plate is dragging between two walls by a velocity of 0.054 m/s. The space between plate and lower wall is 30 mm and filled with oil while the space between the plate and the upper wall is 20 mm and filled with water. The velocity distribution in oil between plate and lower wall is given by: u = 60(0.06y - y), where y is measured in m and u in m/s. determine the force p that is required to maintain the velocity of plate when the area of plate is 1 m?. Epper wall Water Plate Lewer mall

2) A Plate is dragging between two walls by a velocity of 0.054 m/s. The space between plate and lower wall is 30 mm and filled with oil while the space between the plate and the upper wall is 20 mm and filled with water. The velocity distribution in oil between plate and lower wall is given by: u = 60(0.06y - y), where y is measured in m and u in m/s. determine the force p that is required to maintain the velocity of plate when the area of plate is 1 m?. Epper wall Water Plate Lewer mall

Name: 2) A Plate is dragging between two walls by a velocity of 0.054 m/s.
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 2) A Plate is dragging between two walls by a velocity of 0.054 m/s. The spacebetween plate and lower wall is 30 mm and filled with oil while the space betweenthe plate and the upper wall is 20 mm and filled with water. The velocitydistribution in o

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
Express Newton’s first, second, and third laws.
A block of mass m slides along a horizontal surface lubricated with a thick oil which providesa drag force proportional to the square root of velocity.F_d=-bv^1/2If v = v0 at t = 0, determine v as a function of time
aerodynamics: Determine the difference between the total pressure of an aircraft flying at sea level, and an aircraft flying at 5KM? Both have a velocity of 100m/s.
A jet of liquid is directed vertically upward. At A its diameter is 75 mm and its velocity is 9 m/s. Neglecting air friction, determine its diameter at a point 3 m above A.A.104 mm.C.100mm.B.102 mm.D.106mm.
A vertical cylindrical container contains 5840 gallons of gasoline and is 1.53 m in radius. Due to evaporation within the tank, the pressure on the top of the fluid is 2.5 times normal atmospheric pressure. The density of gasoline is 737 kg/m3. a. What is the pressure at the bottom of the tank? b. If a nozzle at the bottom of the tank is used to let fuel out, with what velocity would the gasoline exit the hole? c. If a nozzle at the bottom of the tank is used to let fuel out, what volume flow rate will result if the diameter of the hole is 1.2 cm? d. At what initial rate will the height of the fuel level in the tank drop as fuel is removed?
A water jet of an area of 0.03 m² impinges normal on a fixed plate. If a force of 1 kN is produced as a result of the impact, the velocity of the jet would be
A sled with two runners slides along a thin horizontal layer of water between the ice and the runners. The horizontal force that the water puts on the runners is equal to 2.4 lb when the sled's speed is 50 ft/s. The total area of both runners in contact with the water is 0.04 ft2, and the viscosity of the water is 3.5x10 lbs/ft2. Determine the thickness of the water layer under the runners. Assume a linear velocity distribution in the water layer.
Water flowing in a pipe reaches a point where the cross-sectional area of the pipe is reduced to 1/3 of its previous value. If the speed of the water before the constriction is 1.31 m/s, what is the speed of the water after the constriction?
An unknown gas is flowing through a venturi meter whose diametersas shown. Gage pressures are measured 12.2 psia at the entranceand 11.8 psia at the throat. Take the density to be 0.105 lb/ft3.Determine the following: a) Neglecting friction, the volume flow rate of air b) If the pressure gauge is replaced with a manometer withmercury as its medium (SG=13.6), what will be the height ofthe mercury in inches? Draw the most possible orientationof the manometer and its fluid height.
An open tank 5m long, 2m deep and 3 m wide contains oil of relative density 0.9 to a depth of 0.9 m. If the tank is accelerated along its length on a horizontal track at a constant value of 3 m/s2 , determine: (i) The new positon of the oil surface. (ii) The pressures at the bottom of the tank at the front and rear edges. (iii) The amount of spill if the tank is given a horizontal acceleration of 4.5 m/s2 instead of 3 m/s2 .
Figure 13 shows a steady flow of 40 kg / s of water at 20 ° C through a nozzle if D1 = 18 cm and D2 = 5 cm calculate the average velocity in meters per second in (a) section 1 and (b) section 2