Answered: What time (in second) is required to…

Name: Select one:a. 41.94b. 18.52C. 14.19d. 12.87e. 25.59 What time (in sec
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Select one:a. 41.94b. 18.52C. 14.19d. 12.87e. 25.59 What time (in second) is required to fill the circulartank with incompressible water from h= 2 m toH=8.5 m?D=20 cmHwaterd1= 4cmv1-5 m/sd2=3 cmv2=2 m/s1,

Engineering

Mechanical Engineering

What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to H=8.5 m?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
A pipe has a cross-sectional area of 16.5cm2 at point A, where the speed of the fluid (water) is 1.2 m/s and the pressure is 2.00 atm. The pipe ascends 3.00 m and narrows to 8.20 cm2 at point C. a) what's the speed of the fluid at point C. b) what's the absolute pressure at point C.
Q5: The U-tube shown in figure (3), in filed with water and rotated about a vertical axis (0.15m) to the right of (A) For a gage pressure at (A) equal to zero Determine the rotational speed in (r.p.m)
Q1:- (a) Show that stream function exists as a consequence ofequation of continuity.(b) Show that potential function exists as a consequence ofirrotational flow
Piston A has a cross-section of 1,200 cm^2 while that of piston B is 950 cm^2 with the latter higher than piston A by 1.75 m. If the intervening passages are filled with oil (s= 0.8), what is the difference in pressure between A and B?
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. a. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? b. After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? c. What will be the absolute pressure (P3) in the smaller pipe? d. What is the volume flow rate through the smaller pipe?
Find the resultant force in the y-direction Fr,y for a volumetric flow rate in the y direction of 100 L/hr, a pressure of 150 kPa, and a diameter of 3 cm. Use the equation Fr, y = -m1y1 - P1A1
In the system given in the figure, the top of the container and the pipe outlet aresince it is open;a) The volumetric flow of water (L / s) at the pipe outlet,b) Calculate the pressures at A and B points.H = 151 m,h = 121 mPipe diameters D1 = 40 cm, D2 = 150 mm
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
The water level in the 1.8 m high and 1 m diameter cylindrical tank in the figure is 1.4 m. If this tank is rotated around its own axis at what speed will the axial depth be zero? (In other words, what is the number of revolutions at which a dry area will begin to form at the bottom of the tank?) Take the gravitational acceleration as 10 m / s2 and π as 3.