= 2-)A single-phase bridge (full-wave) Inverter with 300W output power Is supplled with 200V DC voltage. The output voltage of this Inverter is controlled so that there Is one trigger (pulse) In every half period. Find the THD value for the output voltage by performing the harmonic analysis of the output voltage waveform. If the output L= load RL with 2mH content, obtain the equation of the output current. Obtain the output current maximum value and effective value.

= 2-)A single-phase bridge (full-wave) Inverter with 300W output power Is supplled with 200V DC voltage. The output voltage of this Inverter is controlled so that there Is one trigger (pulse) In every half period. Find the THD value for the output voltage by performing the harmonic analysis of the output voltage waveform. If the output L= load RL with 2mH content, obtain the equation of the output current. Obtain the output current maximum value and effective value.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Perform a 1000 case Monte Carlo analysis forthe noise margins of the inverter if thethreshold voltage has a tolerance of 10 percent,the power supply has a 5 percent tolerance andKn and R both have 30 percent tolerances. Whatare the nominal, minimum and maximum values ofNML and NMH ? (b) Compare the results
Design an asymmetrical inverter to meet the delay of 250 ps for a load capacitance of 120 fF. Use VDD =1.5V, VTN =0.50 V, and VTP =−0.50 V. with (W/L)P = (W/L)N .
1. In a full-bridge single-phase inverter with an input voltage of 200V and a switchingfrequency of 4kHz, the power of a 16Ω load is controlled by the method of a gappedsquare wave control. Ignoring the circuit losses, answer the following questions a. Draw the inverter circuit presented in the question b. Generate PWM signals for a duty ratio of ½. Draw the load voltage, load current. Drawthe current and the voltage of any of the semiconductors. Find the load voltage. Find theoutput voltage frequency c. Find the nominal (the maximum) power and current of the load d. Find the duty ratio to get half of the nominal voltage e. Find the duty ratio to get a quarter of the nominal power f. Find the average value and effective value of BJT current for the case of item-e
(a) What is the power-delay product for a symmetrical CMOS inverterwith (W/L)N =2/1, (W/L)P =5/1, C =0.25 pF,VDD =3.3 V, VTN =0.75 V, and VTP =−0.75 V? (b) Estimate the maximum switchingfrequency for this inverter. (c) Howmuch powerdoes the inverter dissipate if it is switching at thefrequency found in (b)?
If,for a single phase half bridge inverter the amplitude of output voltage is Vs and the output power is P then their corresponding values for a single phase full-bridge inverter are a. 2Vs,2P b. 2Vs,4P c. 2Vs,P d. Vs,P
Justify the usage of the RCD (residual current device ) at the AC side of the inverter? You have to explain its operation prinviple
The logic swing in the inverter as shown is reducedby a factor of 3 by reducing the value of RCand changing VREF. What is the new value of VREF?What is the new value of the power-delay product?
Find the ratio of hole mobility to electron mobility of a CMOS inverter given that the beta ratio of pull-up network to pulldown network is 1.5 (Assume that W/L ratio of pMOS is 3 times greater than that of nMOS and all other parameters are same for both) Assuming the supply voltage to be 3V draw a suitable DC transfer characteristic curve of the CMOS inverter.
Q1: Design a combinational circuit with four inputs lines that represent a decimal digit in BCD and four output lines that generate the 9’s complement of the input digit. Q: 2 Show how a full adder can be converted to full-subtractor with the addition of one inverter circuit.
A resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. Sketch the waveforms of load voltage, fundamental component of load voltage, fundamental component of load current, current through any one device and voltage across any device .
For an inverter circuit where the load is RL circuit, the value of Zn, and In increase as n increase. True or False ?
For an inverter with VIL = 0.46 V, VIH = 0.77 V, VOL= 0.08 V, and VOH = 1.2 V, find out the maximum value for the noise voltage in presence of which the inverter can work properly. Ans: 0.38 V.