Q: Design the duct system by using velocity reduction method andfindFTP andtheamountof dampering required.Assumeadynamic loss coefficient of0.3for downstream and 0.5forupstreamtobranchandfortheelbow.Thedynamiclosscoefficients for the outlets may be taken as 1.0.1m'/s10 m2 m /s30 m9 m/sFAN30 m45 m10 m1m /s

Answered: Image /qna-images/answer/a214c7a8-b96b-4d29-b8a3-b082f6aa9890.jpg

2: Design the duct system by using velocity reduction method an Eind FTPmax dynamic loss apstream coefficients for the outlets may be taken as 1.0. and the amount of dampering required. Assume coefficient of 0.3 for downstream and 0.5 to branch and for the elbow. The dynamic lo

2: Design the duct system by using velocity reduction method an Eind FTPmax dynamic loss apstream coefficients for the outlets may be taken as 1.0. and the amount of dampering required. Assume coefficient of 0.3 for downstream and 0.5 to branch and for the elbow. The dynamic lo

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is 200 mm and is characterized by a fri factor of 0.02. The design discharge is 0.15 m³/s and the pump. Assuming th minor losses are 20% of friction losses, determine the head the pump must p
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
Suppose the pump of Fig. P14–23 is operating atfree delivery conditions. The pipe, both upstream and downstreamof the pump, has an inner diameter of 2.0 cm andnearly zero roughness. The minor loss coefficient associatedwith the sharp inlet is 0.50, each valve has a minor loss coefficientof 2.4, and each of the three elbows has a minor losscoefficient of 0.90. The contraction at the exit reduces thediameter by a factor of 0.60 (60% of the pipe diameter), andthe minor loss coefficient of the contraction is 0.15. Note thatthis minor loss coefficient is based on the average exit velocity,not the average velocity through the pipe itself. The total length of pipe is 6.7 m, and the elevation difference is (z1 - z2)= 4.6 m. Estimate the volume flow rate through this pipingsystem. Complete Answer, Thank you
The horizontal pipe length is 180 m and the vertical pipe length is 24 m in the fire protection system, which is formed with a water tower and pipeline, 1 threaded 90 ° elbow (Kd = 0.9) on the pipeline and 1 slide valve at the pipe outlet (fully open position Kv = 0.2). Since the pipe material is cast iron and its diameter is 4 ”(101.6 mm), determine the maximum flow rate in the pipe considering the losses. Assume that the water level in the tower remains constant and the kinematic viscosity of the water is 1.124x10-6 m2 / s. Show your readings by drawing on the attached Moody diagram.
The water is flowing througha pipe having diameters 20 cm and 10 cm at sections 1and 2 respectively. The rate of flow through pipe is 0.035 m /s. The section1 is 7500 mm above datunm and section 2i5 500 cm above datum. If the pressure at section 1 is 420 kPa, find the intensity of pressure at section 2.
A duct of rectangular cross-section 600mm X 400mm carries 90 m3/min of air having a density of 1.2 kg/m3. Determine the equivalent diameter of a circular duct, (a) when the quantity of air carried in both the cases is the same; and (b) when the velocity of air in both the cases is the same. If friction factor is 0.011, find the pressure loss per 100 m length of duct. Group of answer choices 537 mm; 480mm; 21.9 mm of water 750 mm; 408mm; 12.9 mmof water 573 mm; 840mm; 29.1 mmof water 735 mm; 804mm; 91.2 mmof water please give full solution for review and analysis
The old Hydraulics laboratory in Mechanical Engineering used a roof tank tosupply apparatus with water at a nearly constant head. The water wascollected in an under floor sump, and then pumped back to the roof tankafter the experiment. The flow rate was 10 litre s-1. The tank was 6m abovethe sump, and the length of the pipe route was 15 m. The old 6” pipes arenow heavily corroded (k = 7.5 mm). The old pump has been scrapped. Whathead ΔH would be specified for a pump to restore the system using the oldpipes? What would the pump power be? If the pipes were replaced with 150mm diameter PVC pipes, what pump ΔH would be required?
Convert 104KPa to meters of H2O @ d= 15mm = 225psi to inches Hg in a pipe of circumference = 130000π μm
Water is pumped from a reservoir to a pressurized storage tank (P = 150 kPa gauge) atop a building by means of a centrifugal pump. There is a 70-m difference in elevation between the water surface in the reservoir and the end of the discharge line. The piping system consists of 80m of 5" SCH 40 steel pipe containing two 90o elbows, one gate valve, one rotary water meter, and six couplings from the reservoir to the pump; 3" SCH 40 steel pipe for 86m to the tank. The 3" pipe contains two gate valves, four 90o elbows, and ten couplings. It is desired to maintain a flow of water into the tank of 2.4 m3/min. Water temperature is 25oC. If the pump-motor set has efficiency of 65%, what would be the pumping costs be in pesos per day if electricity costs PhP 10.50/kW-hr?
A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing at 70°F and 60 psig. The entrance to the pipe is sharp-edged, and the 70-ft-long piping system involves three 90° miter bends without vanes, a fully open gate valve, and an angle valve with a loss coefficient of 5 when fully open. If the system is to provide water at a rate of 15 gal/min and the elevation difference between the pipe and the fountain is negligible, determine the minimum diameter of the piping system.
Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 1.64 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.94 m.
Water is being pumped from reservoir A (elev. 24.57 m.) to reservoir B (elev. 50.94 m.) as shown. The total length of pipe is 862 meters, diameter of 572 mm., and friction factor of C = 117. The rate of flow in the system is 0.632 m3/s. Compute the power generated by the pump in kW. Assume pump is 100% efficient.