2- Why it's imporctical carry out actual load test on large rating transformers ? woVoW2VI12Step adjustableAuto – transformerAuto - transformerFig.1

For large-rated transformer, the value of the rated current is usually very high.

Answered: 2- Why it's imporctical carry out…

Engineering

Electrical Engineering

2- Why it's imporctical carry out actual load test on large rating transformers ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.16MCQ: In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across...

See similar textbooks

Related questions

Q: What is Per Unit System? In the given picture, would there be any difference in calculation of the…

A: The per-unit value of any quantity is defined as the ratio of actual value in any unit to the base…

Q: What is the purpose of polarity testing in order to properly perform paralleling of transformers?

A: Polarity test define the direction of the current. it helps the interconnecting the primary and…

Q: Q1/ Equipment ratings for the four-bus power system shown in Figure are as follows: Generator G1:…

Q: How many types of winding in distribution transformers? What is the impact of each type on…

A: There are three types of windings: Single Helical Winding. Double Helical Winding. Disc-Helical…

Q: 2- Why it's imporctical carry out actual load test on large rating transformers ?

A: Since 2 and 3 are two different questions, as per the guidelines, only the first question (2) has…

Q: Discuss the circumstances where parallel operation of transformers may be a) considered beneficial.

A: Electrical machines can be either generator ,transformers or motors. They can be either AC machines…

Q: What is surge impedance?

A: Surge impedance is also known as the characteristics impedance of the lossless transmission lines.…

Q: B/ Short answer questions 1- What is the function of instrument transformers? 2- What are the…

A: In this question we will write about instrument transformers, core type and shell type…

Q: Why it's imporctical carry out actual load test on large rating transformers ?

A: The explanation is as follows.

Q: Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltage…

A: I have solved for both parts

Q: How does field distortion affect commutation ? ( DC GENERATOR QUESTION)

A: The armature reaction cause the alteration with the main field and cause the demagnetization or the…

Q: Does winding geometry in transformers (winding method) have an effect on zero sequence impedance…

Q: Why is zero sequence impedance important in Zigzag transformers and grounding transformers

A: Why is zero sequence impedance important in Zigzag transformers and grounding transformers?

Q: A three phase synchronous generator with negligible resistance and Xs=20 ohm has induced voltage as…

A: Given: Per phase quantities, Induced voltage E=230 VTerminal voltage V=230 VSynchronous reactance…

Q: (c) Explain the losses of a real single-phase transformers.

A: In this question we will write about single phase transformer losses....

Q: why is there preferable use isolating transformers with cascade transformer unit , if the power…

A: Autotransformers are also known as Isolation Transformer. This is due to the fact that their…

Q: 4. What do you mean by transformer connection Ydl and Dy11?

Q: Q14. In paralleling of synchronous generators, the machines that are to be paralleled must have the…

A: Conditions for parallel operation of alternators (synchronous generators) : -Bus bar voltage of the…

Q: A 50 MVA 230/115-kV, A-Y three-phase connected power transformer has a per unit resistance of 0.015…

A: Need to find the excitation branch element Rc on the low voltage side solve as below

Q: Explain vector grouping of transformers with suitable diagrams. Mention its usefulness.

A: The three-phase transformer can be imagined as a three single-phase transformer having a common…

Q: Mention the types of iron cores in the transformers and the effect of the shape of the iron core in…

A: Iron Cores are also part of transformers

Q: A 50 MVA 230/115-kV, A-Y three-phase connected power transformer has a per unit resistance of 0.015…

A: Given rating of transformer : 50 MVA HV side 230 V assuming primary side LV side 115 V assuming…

Q: Q1: What is the influence of transformer connections in single-phase transformers connected for 3-…

A: According to the Bartleby guidelines “Since you have asked multiple question, we will solve the…

Q: What are the reasons for using transformer oil in power transformers and why are mineral oils…

A: The explanation is as follows.

Q: B) State the main points that should be taken in to account in selection of number and sizes of the…

A: B) The main points that should be taken into consideration while selecting the number and the sizes…

Q: The per-unit system calculations method eliminates the need for explicit voltage-level conversions…

A: in the per-unit system each voltage is represented in terms of its base value

Q: Consider a 3-phase transmission line operating at 66 KV and connected through a 1000 KVA transformer…

Q: ) the internal voltage of the generator and

A: Per unit (pu) system - Per unit (pu) system is used to express system quantity in the form of ratio…

Q: Four similar synchronous generators are sharing equally the feed to a load of 1 pu referred to the…

A: To find the correct option from the given statements

Q: What is the definition of zero sequence impedance in transformer? What is the benefit of zero…

A: Transformer: A device which transfer a electrical energy from one circuit to another circuit…

Q: A 50-kVA 13.8-kV/208-V (rms, line-line) ∆−Ythree-phase distribution transformer has a per-unit…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: In Back To Back Test on Two Similar Single Phase transformers. What will be the current in the…

Q: UDng a ITIe Core in high frequency transformers. c- Discuss, different applications of iron cores of…

A: C)For magnetizing or demagnetizing a iron material, some energy is expended. The energy expended…

Q: Problem 2 Two shunt generators A and B operate in parallel and their load characteristics maybe…

A: Here Two shunt generators A and B operate in parallel load characteristics are straight lines of…

Q: 2- What are the differences between core and shell type transformers? 3- The iron losses is constant…

A: In this question we will write about core type and shell type transformers differences....

Q: Two generating units rated for 500 MW and 400 MW have governor speed regulation of 6.0 and 6.4…

A: Here speed governor is given and we need to find new speed governor at 1000MW base

Q: Q2. (a) Explain what is per unit system? What are the advantages of per-unit computations? Prove for…

A: PU system: Per Unit system is a quantity expression system used in an electrical power system which…

Q: in distribution transformers; What is 30 degrees phase shift in delta-star connection? What are the…

A: In the star-delta connection, the primary side of the transformer is in delta configuration while…

Q: Describe the generator control Schemes for wind electric Schemes

A: Wind generators function on a easy principle. The electricity within the wind turns or three…

Q: What is the reason for drop in Generator’s Terminal voltage, from No load to Full load?

Q: 5. Explain the effect of load power factor on the transmission efficiency?

A: Power factor expresses the ratio of true power used in a circuit to the apparent power delivered to…

Q: 2- Why the transformer core made from lamination plates?

A: We are authorized to answer the first question since the exact one wasn’t specified. Please submit a…

Q: A MVA, 20 KV, three-phašė ģenēřātor has a subtransient reactance of 20%. The generator supplies a…

A: Solution- For generator, S = 300 MVA V = 20KV X = 20% For motor 1, S = 200 MVA V = 13.2 KV X= 20%…

Q: what is the definition of zero sequence impedance in a transformers? And what is the benefit of this…

A: Sequence Impedance The sequence impedance of the network describes the behaviour of the system…

Q: Find the per-unit sub transient current at the fault, in the generator, and in the motor

A: Find the per-unit sub transient current at the fault, in the generator, and in the motor?

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

Transcribed Image Text:2- Why it's imporctical carry out actual load test on large rating transformers ?

wo
Vo
W2
VI
12
Step adjustable
Auto – transformer
Auto - transformer
Fig.1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum volt-ampere rating of transformers supplying Class 2 systems? ___________
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
Three single-phase two-winding transformers, each rated 25MVA,54.2/5.42kV, are connected to form a three-phase Y- bank with a balanced Y-connected resistive load of 0.6 per phase on the low-voltage side. By choosing a base of 75 MVA (three phase) and 94 kV (line-to-line) for the high-voltage side of the transformer bank, specify the base quantities for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this load resistance on the chosen base.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
Consider the adopted per-unit system for the transformers. Specify true or false for each of the following statements: (a) For the entire power system of concern, the value of Sbase is not the same. (b) The ratio of the voltage bases on either side of a transformer is selected to be the same as the ratio of the transformer voltage ratings. (c) Per-unit impedance remains unchanged when referred from one side of a transformer to the other.
2- Why it's imporctical carry out actual load test on large rating transformers ?
2- Why it's imporctical carry out actual load test on large rating transformers ?3- What will be the current in the primary windings?i) When secondaries are not loaded ?ii) When secondaries are loaded ?
The dangers and failure in it and How can we be protect from these dangers and defects of Three-phase distribution transformers?
1- What are the advantages and disadvantages of Back To Back Test on Two Similar Single Phase transformers test ?