2.) A 350 mm x 500 mm rectangular beam is reinforced for tension only with 5-28 mm bars. The beam has an effective depth of 446 mm. The beam carries a uniform dead load of 4.5 kN/m (including its own weight), a uniform live load of 3 kN/m, and concentrated dead loads of P and 2P as shown in the figure. Assume fy = 414 MPa, f'c = 34.50 MPa. Calculate the ff: %3D %3D a.) The ultimate moment capacity of the concrete section in kN-m b.) The maximum value of P in kN 2P P A B 2m 2m 2m

2.) A 350 mm x 500 mm rectangular beam is reinforced for tension only with 5-28 mm bars. The beam has an effective depth of 446 mm. The beam carries a uniform dead load of 4.5 kN/m (including its own weight), a uniform live load of 3 kN/m, and concentrated dead loads of P and 2P as shown in the figure. Assume fy = 414 MPa, f'c = 34.50 MPa. Calculate the ff: %3D %3D a.) The ultimate moment capacity of the concrete section in kN-m b.) The maximum value of P in kN 2P P A B 2m 2m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam reinforced for tension has b = 300 mm, d = 480 mm. The beam is reinforced with 7 of 25 mm bars with fc’ = 21 MPa, fy =415 MPa. If the beam is a cantilever beam 3 m long and supports a uniform dead load of 15 kN/m(including its own weight) applied along its entire length, The maximum value of the concentrated live load that can be applied at the free end is _____kN.
A rigid beam ABC is supported at C by a pin support, and at A and B by timber struts AD and BE which are in turn supported by pin supports at D and E respectively (Figure 1). The struts AD and BE are constructed using F11 timber (refer Figure 2) with square cross section 40 mm x 40 mm. A uniformly distributed load of 10 kN/m acting horizontally to the right is applied along the complete length ABC. Under the action of this load, in addition to any changes in the lengths of the struts, the pin support at C settles by 1 mm to the right. Assume that the beam and struts are weightless and that the struts will not buckle. (a) Using equilibrium and compatibility considerations determine the support reactions at C, D and E. Hint: Since the struts AD and BE can transfer only axial force, the reactions at D and E act horizontally (that is, there are no vertical reaction components at D and E). (b) Find the normal stress, normal strain and change in length of strut AD.
A triangular wooden beam width 150 mm base and 300 mm height carries two concentrated load of 20 kN at third points. If the simple span of the beam is 6 m. Compute the maximum shearing stress of the beam. a. 0.58 MPa b. 1.33 MPa c. 0.48 MPa d. 0.86 MPa
A beam 281 mm wide and effective depth 511 mm carries a factored uniformly distributed load of 66 kN/m including its own weight, in addition to a concentrated factored load of 48 kN at midspan. It spans 5.06 m face to face of simple supports. It is reinforced with ρ = 0.67 ρbal for positive bending. Use f’c = 32 MPa and fy = 414 MPa. Calculate the D/C ratio in percentage (%) for the particular beam.
Answer is 260 mm..don't solve incorrect beam is supported by a roller and a hinge at its extremities. The 2 kN/m is loaded entirely on its 4 m length while 5 kN concentrated load is positioned 2 m from the left end of this beam. If the beam is 80 mm wide, determine the minimum height of the beam if the flexural stress is not to exceed 10 MPa.
A cantilever R.C. beam is 280 mm x 500 mm deep and is reinforced with 4- 20 mm diam bars for tension. Using an effective depth of d = 450 mm, determine if the 2.50 m long beam is adequate to carry a uniform load of 15 KN/m and a concentrated load of 10 KN at the cantilever end in 2 ways. Use f’c = 21 MPa, fy = 275 MPa. Neglect the weight of beam. Use n = 9.Determine if the catilever beam is adequate based on strength design 2001 NSCO specifications. The 15Kn/m load is DL while the 10KN load is LL.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
A reinforced concrete beam (300mm by 500mm) with effective depth of 440mm is 5 meters long and supports a uniform load of 15 KN/m and a concentrated load of 30 KN at the midspan of the beam. a. find the max. moment experienced by the beam b. find the location of the neutral axis from the bottom of the beam if it requires 6-16mm diameter bar needed for tension only. assume n=10 c. What would be the stress developed in the concrete and steel. d. compute for the moment of inertia
A 7-meter simple beam is loaded with a varying load that varies from 0 kN/m to 40 kN/m applied at 1 m and 4 meters from the left support respectively. Compute the 6Ab/L of the beam.
Question 19 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the ultimate moment capacity in kN∙m of the beam in negative bending. 42.79 40.56 47.55 45.07
reinforced concrete T-beam has an effective depth of 600 mm and is reinforced at the bottom with steel area of 4926 mm2. The web width is 300 mm and has a flange thickness of 100 mm. The beam has a span of 6 m and has a spacing center to center equal to 1.8 m. ??′=21 MPa ??=415 MPa. Determine the following:a. Effective width of the flangeb. Depth of the compression blockc. Nominal moment capacity of the beam
A wooden beam 150mm wide by 300mm deep is loaded as shown. If the maximhm flexural stress is 8MN/m^2. Find the maximum values of1.)W(kN/m)2.) P (kN)