2. a) An electronic warning system has a switch labelled A and two sid. panels B and C. The output Q of an electronic warning system triggen an alarm if the enable switch A is turned on and either panel is open, o both are open. B and C produces an output of logic 0 signal when closed The enable switch A sends a logic 1 signal to the electronic system whes turned on. The system outputs a logic 1 to trigger the alarm. Draw a truth table for the electronic warning system described above. ii. From the truth table, derive and minimize the canonical SOP Form Draw the logic circuit for the electronic warning system inimion i.

2. a) An electronic warning system has a switch labelled A and two sid. panels B and C. The output Q of an electronic warning system triggen an alarm if the enable switch A is turned on and either panel is open, o both are open. B and C produces an output of logic 0 signal when closed The enable switch A sends a logic 1 signal to the electronic system whes turned on. The system outputs a logic 1 to trigger the alarm. Draw a truth table for the electronic warning system described above. ii. From the truth table, derive and minimize the canonical SOP Form Draw the logic circuit for the electronic warning system inimion i.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A simple burglar alarm is to be wired up in a house which has two access doors, A and B. Micro switches are used todetect whether the doors are open or closed with a logic level 0 detected when a door is closed and a logic level Itransmitted when a door is open. The alarm system can also be activated ON and OFF through a concealed manualswitch S. with the system activated; a logic level I is transmitted through switch S. A logic level 0 through switch Sindicates that the system is OFF Devise an appropriate Boolean expression to represent the sound of the alarm Fwhen the system is activated and either, or both, of the doors are opened. construct a circuit diagram for the alarm system and deduce the appropriateBoolean functions:(a) Using NAND gates only.(b) Using NOR gates only
Draw the logic circuit diagram. Don't give hand-drawn diagram
simple burglar alarm is to be wired up in a house which has two access doors, A and B. Micro switches are used todetect whether the doors are open or closed with a logic level 0 detected when a door is closed and a logic level Itransmitted when a door is open. The alarm system can also be activated ON and OFF through a concealed manualswitch S. with the system activated; a logic level I is transmitted through switch S. A logic level 0 through switch Sindicates that the system is OFF Devise an appropriate Boolean expression to represent the sound of the alarm Fwhen the system is activated and either, or both, of the doors are opened.
Need Part B (a) Suppose a two-way switch logic needs to be implemented in a staircase of a building, where a lamp can be controlled by two switches. You are required to analyze below conditions, and provide a PLC based system capable of operating according to the below mentioned conditions • If both the switches are in same state, i.e., both are off or both are on, then lamp will be in "ON" state. If anyone of the switches is "ON" and other is "OF", then lamp will be in "OFF" state. When the lamp is OFF, users can turn it on by changing the state of either switch 1 or switch 2. • Likewise, when the light is ON, users can turn off the light by changing the state of one of the two switches. 2. Suppose you are required to control a motor ON, OFF operation with two push buttons using PLC. Control System should work according to following conditions: When motor is off, and 1" push button is pressed, motor will start and stay in on state even after release of push button. When 2nd push…
can tutor answer the questions related to the diagram I provide as it seen like general answer which not related to the diagram I had provide Q1: What inputs and output does the system detect and where are these locations? Q2: What logic gates are used for the landing gear warning logic module? The diagram below is the case study
choose the correct answer Noise margin is the amount of? a. None of the choices are correct b. both signal and noise voltage that a logic gate can tolerate c. signal voltage that a logic gate can tolerate d. noise voltage that a logic gate can tolerate
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG
LOGIC GATE ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
Write the truth table and logical expression and draw the pin diagram and logical symbol of a two input HEX NOT Gate IC.
draw and identify or explainMake na input circuit using a switch and an external pull-up resistor.What are the logic states of the microcontoller if the switch is open?What are the logic states of the microcontoller if the switch is off?
Assignments 1- What is the number of digital pins in Uno and mega boards? 2- What is the number of analogue pins in Uno and mega boards? 3- What is corresponding voltages for logic 0 and logic 1? 4- What is the voltage range for input powering voltage? 5- What is the number of output bits of analogue input? 6- What is the range of analogue inputs voltage? 7- Give the instruction used for digital input? 8- Give the instruction used for digital output? 9- Explain the delay instruction? 10- Give detail information about Arduino Uno board including the used MCU, no. of digital and analogue pins, its memory and any other important information?11- Give detail information about Arduino Mega board including the used MCU, no. of digital and analogue pins, its memory and any other important information? 12- What does the term IDE refer to? 13- What does the term sketch refer to? 14- What does the term software library refer to? 15- What does the term…
Draw simple logic gate for door actuator from the following NOT card access reader OR NOT body temp sensor AND NOT emergency overide = Output(Door actuator)